18
4
6
7
9
9
5
LINKOUT
LEVEL
PV
OFF ON
0 10
1
2
3
456
7
8
9
R
CONTOUR
POWER
CLIP
INPU T
VOLTAGE SELECTOR
FULL RAN GE SPEAKER OUT
8 OHMS MA X POWER
400W PROGRA M
100-120V
5x20mm
FUSE IN
BOTTOM CAVIT Y
220-240V
ON
POWER
Designed and Engineered in U.S.A.
Made in China
APRODUCTOF PEAVEYELECTRONICS CORP.
DO NOT CH ANGE SWITCH WH ILE UNIT I S ON!
UNPLUG AC COR D AND S EE MANUA L FOR
PROPER OPERAT ION. CHA NGE FU SE SIZE.
This device c omplies with part 15 o f the FCC Rules . Operatio n is
subject to the followin g two conditions:(1)thi s device may no t cause
harmful interference,and ( 2) this dev ice must ac cept anyinterference
received,including interference that m ay cause undesisred operation .
WARNING:T O REDUCE THE RISK O F FIREOR ELECTRIC SHOCK THIS APPARATUS
SHOULD NOT BE EXPOSED TO RAIN OR MOISTU RE AND OBJECTS FILLED WITH LIQUID S
SUCH AS VASES SHOULD NOT BE PLACED ON THIS APPARATUS TO PREVENT THE RISK
OF FIRE HAZARD REPLAC E WITH SAME TYPE 250 VOLT FU SE
.
.
..
.
AVIS:DANS L E BUT DE REDUIRE LE S RISQUES D INCENDIE OU DE DE CHARGE
AUCUN OBJET REMPL I DE LIQUIDE T EL QU UN VASE NE D OIT ETRE POSE SUR CEL UI CI
REMPLACER PARUNFUSIBL E DE MEME TYPE ET DE 25 0 VOLTS
...
.
,
,
,
ELECTRIQUE CET AP PAREIL NE DOIT PAS ETR E EXPOSE A LA PLUIE OU A L HUMIDITE ET.
-
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQE
NE PAS OUVRIR
100-120V /220-240V 50/60H z
370WAT TS
AC CORD
100-120V
fuse T6. 3AL 250V=
220-240V
fuse T3 .15AL 250V=

11 5D

5 6 7 8 9

TOp panel

SPEAKER OUT JACK
This jack allows a full-range passive (unpowered) speaker to be connected to the PV®115D internal power
amp, as long as it has an impedance rating no lower than 8 ohms, and is of similar sensitivity as the PV115D
speaker system. Ideally, this speaker would be the passive model PV115, however, other 8-ohm passive
full-range speakers with a nominal sensitivity of around 95 dB can be used. This additional speaker system
can help increase coverage of the venue. The volume level of this added speaker is controlled at the same
time as the volume of the PV115D, thus the need to use a speaker system with a similar sensitivity.
It can also be used to drive an 8-ohm impedance non-powered subwoofer with a built-in high-frequency
roll-off, such as the PV-118 Sub.
INPUT JACK
The line level input is of the medium impedance balanced type. Jack (5) is a combo female XLR and 1/4”
TRS connector, and can be supplied a balanced or unbalanced input signal.
LEVEL
Controls the gain (volume) of the Input (5) of the powered speaker system.
CONTOUR SWITCH
The Contour switch provides a mild boost at the frequency extremes, so that low level playback can be
more pleasing. Do not use the Contour switch when playing sound at loud levels, as the boost is not
needed then.
LINK OUT
Link Out is a 1/4” pre-level send intended for the use of linking multiple PV®115D’s in a line. In that case,
the Link Out would connect to the 1/4” connections of the MIC/LINE (5) input of the next PV®115D in the
line of PV speakers. Individual speakers can be adjusted by their own Level control(6). This output can
also be used to drive a nearby powered subwoofer, such as the PV®118D Sub. Set the PV®118D Sub level
control to a level that matches that of the output of the PV®115D.
POWER/CLIP LED
Illuminates GREEN when the electronics receive power (when the Power switch (3) is On). Illuminates RED
when amplifier clipping is occurring.