hooks in the front (A) and the rear (B and C). 9• The figure shows the basket fastened to the
stroller.
10• The drink holder can be mounted on the right or left handlebar with the two special bands.
11• To fasten the drink holder to the handlebar, open
the band and press the drink holder into it as shown in the figure, letting it click into place.
•Warning: do not place hot drinks or drinks weighing more than 1 kg. (2.2 lbs) in the drink holder.
BRAKES
12• To set the brakes on Pliko P3 Naked, lower the lever on the rear wheels with your foot, as shown in the figure.
•To release the brakes, lift the lever.
•Always set the brakes when the stroller is not moving.
SWIVEL WHEELS
13• To swivel the front wheels, lower the lever as shown in figure A. To set the wheels on stationary, lift the lever as shown in figure B.
ADJUSTING THE HANDLEBARS
14• The height of the handlebars can be adjusted to two positions. For the higher position, press the button while pulling the handlebar upward. To lower the handlebar, press the button and push the handlebar downward.
FOLDING UP PLIKO P3 NAKED
•Before folding up Pliko P3 Naked, remove the Navetta bassinet unit or Primo Viaggio car seat.
15• The stroller can be folded up using one hand only. Pull first one lever upwards and then the other, until they click.
16• Grab the central handlebar (Figure 3) and pull upward until the stroller folds up, as shown in the figure.
17• Check to make sure that the safety hook is fastened. The folded stroller will stand upright.
CARRYING
18• Pliko P3 Naked can be conveniently carried (with the front wheels set on stationary) when held by the central handle, as shown in the figure.
19• The side handle can also be used to carry the stroller, as shown in the figure.
THE GANCIOMATIC SYSTEM with
THE PLIKO P3 NAKED CHASSIS
The Ganciomatic system is a practical, fast way to fasten the Navetta bassinet unit and the Primo Viaggio car seat – which are both equipped with the Ganciomatic system - to the Pliko P3 Naked chassis, using the Ganciomatic hooks.
GANCIOMATIC HOOKS ON THE CHASSIS 20• To raise the Ganciomatic hooks on the chassis,
turn them upwards until they click into place, as shown in the figure.
21• To lower the Ganciomatic hooks on the chassis, pull the lever outwards while turning the hooks downwards, as shown in the figure.
PLIKO P3 NAKED + NAVETTA
To fasten the Navetta bassinet unit to the Pliko P3 Naked chassis, first:
-Set the brakes on the Pliko P3;
-Raise the Ganciomatic hooks;
22• Turn the two levers on the rear of the chassis outwards, as shown in the figure;
23• Lift the chassis footboard to its highest position (Figure 1);
24• The Pliko P3 Naked chassis is now ready for
attaching the Navetta bassinet unit;
25• Hold the Navetta bassinet unit by its handle, and place it on the Ganciomatic hooks on the chassis, keeping the head of the bassinet unit on the opposite side from the chassis handlebars.
-Press down with both hands on the sides of the Navetta bassinet unit, until it clicks into place.
-To remove the Navetta bassinet unit from the chassis, consult the instruction manual.
PLIKO P3 NAKED + PRIMO VIAGGIO
To fasten the Primo Viaggio car seat to the Pliko P3 Naked chassis, first:
-Set the brakes on the Pliko P3;
-Attach the front bar (see the “Front Bar” section below).
26• The Pliko P3 Naked chassis is now ready for attaching the Primo Viaggio car seat.
27• Hold the car seat by its handle, and place it on the Ganciomatic hooks on the chassis, keeping the head of the car seat on the opposite side from the chassis handlebars. Press down with both hands on the sides of the car seat, until it clicks into place.
-To remove the car seat from the chassis, consult the instruction manual.
FRONT BAR
28• The chassis comes with caps closing the ends of the armrests. To fasten the front bar to the chassis, remove the caps (keep them for when you want to use the chassis without the front bar). To remove the caps, press the buttons under the armrests while pulling the caps off.
29• To fasten the front bar to the chassis, slip the two ends of the front bar into the armrests as shown in the figure, pressing until the bar clicks into place.
30• The front bar can be opened on one side only to allow the child to get in and out of the stroller easier when he or she is older. To open the front bar, press the button under the armrest while pulling the front bar outwards.
31• To remove the front bar, press the two buttons under the armrests while pulling the bar off the chassis.
HOW TO TURN THE CHASSIS INTO A STROLLER
ASSEMBLY
32• To turn the Pliko P3 Naked chassis into a stroller, make sure the two levers are lowered as shown in the figure.
33• Place the backrest with the sack on the seat of the chassis, as shown in the figure.
34• To fasten the backrest to the chassis, insert the two ends of the backrest into the seat of the chassis while pressing the two buttons, as shown in Figure 1. Press on the backrest until it clicks into place, as shown in Figure 2.
35• To attach the backrest adjustor to the chassis, turn the fastener upward (Figure B – turn in the direction shown by the arrow), placing it behind the rear brace.
36• Push the two fasteners downward until they click into place on the braces.
37• To line the stroller, fasten the sack to the armrests as shown by the arrows in the figure.
38• Insert the footboard levers into the sack on the backrest, as shown in the figure.
39• Finally, fasten the buttons on the sack at the bottom, as shown in Figure A. Pass the lower leg divider belt under the seat, as shown in Figure B, and leave the upper leg divider over the sack.
OPENING AND FOLDING UP
• To open the Pliko P3 Naked stroller, repeat the