•Skate-seat

•Bumper bar

•Hood and cover

•Rain cover

•Standard adapter set for car seat group 0+ "Primo Viaggio SIP" or "Primo Viaggio tri-fix" Peg Perego.

instructions for use

MOUNTING THE WHEELS

1• Remove the protection caps from the rear wheels. To mount the rear wheels, insert the pins into their housings until they click into place.

2• Before fitting the front wheels, make sure that the indicators on the fastening controls are red. Insert the pins of the wheels in the appropriate housing, making sure that the green lines of the wheels match up with the green lines of the housing. Finally, turn the fastening controls until the indicators are green.

•IMPORTANT: Check that the wheels are secured by pulling them.

OPENING the Skate chassis

3• To open the Skate chassis remove the locking levers (fig. A) from the side pins and push them up until they go back in.

4• If it is in the closed position (fig. A), rotate the handlebar by one position (fig. B, open the two levers outwards, position the handlebar and close the two levers again) to avoid contact with the centralized locking pedal (fig. C).

5• Hold the Skate chassis down with a foot and raise the handlebar until it clicks into place.

Check that the chassis is open properly by making sure that the front of the centralized locking pedal is not red.( If the red part is visible, continue to pull up the handlebar until you hear it click and the red is no longer visible on the centralized locking pedal. The Skate chassis can also be opened when the Skate-seat is attached; after opening the Skate chassis, recline the Skate-seat as needed (see reclining the Skate seat section). IMPORTANT: Sit the child in the Skate-seat only after opening the Skate chassis.

CENTRALIZED BRAKE

6• To apply the brakes, push down with one foot the bars on the rear wheels, as shown in the figure. To release the brakes, draw the bar up.

FRONT SWIVEL WHEELS

7• To set the front wheels to swivel, lift the stopper up, as in figure A. To set the wheels in a fixed position, push the stopper down, as in figure B. When they are turned around, the wheels automatically fix into place.

REAR INFLATABLE WHEELS

8• A pump is attached to the bottom of the frame in the rear of the stroller to inflate the rear wheels. Pull out the cord from the top of the pump and screw it in the figure. Unscrew the wheel valve

cap and screw the cord of the pump.

•Before using the stroller for the first time you are advised to inflate the tires to a pressure of 25 psi/1.7 bar.

•IMPORTANT: Do not inflate the wheels too much; max pressure is stated on the wheel.

HANDLEBAR

•The handlebar of the Skate chassis is telescopic and the handle grip is height adjustable to 3

positions.

9• To extend the handlebar, pull up the two handlebar extender hooks simultaneously and place the handlebar at the height you want it.

10•To adjust in height the handle grip, open the two levers outwards, place the handle grip in the position you want and lock the two levers again.

BOTTLE HOLDER

11•The bottle holder can be attached to both sides of the Skate chassis, To attach it, insert the back of the bottle holder into the housing provided on the Skate chassis.

BASKET

12•The basket is equipped with adjustable elastic straps to secure the contents. Before connecting the straps, place the elastic strings in the suitable position.

REMOVING THE WHEELS

13•To remove the rear wheels from the Skate chassis, pull out the pin while taking off the wheels.

14•To remove the front wheels from the Skate chassis, turn the fixing knobs until the indicators are red, then take off the wheels.

ATTACHING THE Skate-SEAT TO THE Skate CHASSIS 15•Before attaching the Skate-seat to the Skate

chassis, make sure both locking systems are at the same height and rotated to the same position.

16•To attach the seat, insert the legs of the Skate seat into the holes in the Skate chassis until they click into place.

•IMPORTANT: Make sure the Skate-seat is attached properly by pulling it upwards.

•IMPORTANT: This operation is required only if the Skate-seat is in carriage mode and your child weighs less than 9 kg (19.8 Ibs).

RECLINABLE Skate-SEAT

17•The Skate-seat can be reclined to 3 positions (horizontal, partially reclined and reclined) either facing parents or the other way.

•To recline the Skate seat, pull up the handle behind the backrest and adjust the Skate seat to the position you want.

•Skate carriage seat: the Skate-seat must be fully horizontal.

•Skate stroller seat: the Skate-seat can be inclined to the 3 positions available.

Page 15 Page 17
Page 16
Image 16
Peg-Perego SKATE manual Instructions for use
Page 15 Page 17

SKATE specifications

The Peg-Perego SKATE is a remarkable stroller designed to cater to the needs of modern families, combining convenience, versatility, and style. This innovative stroller is perfect for parents who want an adaptable solution that grows with their child, and it makes navigating both urban and suburban landscapes a breeze.

One of the standout features of the Peg-Perego SKATE is its modular design. It allows for multiple configurations, accommodating infants and toddlers with ease. The stroller can be used with a car seat, bassinet, or as a traditional stroller seat, ensuring that it meets the needs of your growing child. The compatibility with Peg-Perego's Primo Viaggio car seat makes it a seamless travel system, providing parents with the option to transition from car to stroller without having to disturb their little ones.

Stability and maneuverability are hallmarks of the SKATE. Its larger rear wheels and front swivel wheels ensure smooth handling on various terrains, whether you are on a busy city sidewalk or navigating a bumpy park path. The adjustable handlebars cater to parents of different heights, making it comfortable for everyone to push.

Safety and comfort are prioritized in the design of the Peg-Perego SKATE. The stroller features a multi-position reclining seat that allows your child to sit up straight or lean back for a nap. Additionally, it is equipped with a five-point harness system, providing security for your child during your outings. The large canopy offers ample sun protection, shielding your little one from harmful UV rays while still allowing for ventilation.

Convenience extends to the SKATE's storage options as well. It comes with a generous shopping basket beneath the seat, enabling parents to carry diaper bags, groceries, or other essentials. The stroller also features a compact fold mechanism, making it easy to store and transport.

Furthermore, Peg-Perego emphasizes quality craftsmanship, with the SKATE being made in Italy using high-quality materials that ensure durability and longevity. Its stylish design does not compromise functionality, making it a fashionable yet practical choice for stylish parents.

In summary, the Peg-Perego SKATE is a versatile stroller packed with features that cater to the safety, comfort, and convenience of both parents and children. Its adaptability, stability, safety features, and stylish aesthetics make it an excellent choice for families on the go.
Top Page Image Contents