HEIGHT ADJUSTABLE Skate-SEAT

18•The Skate-seat is height adjustable to 3 positions: To adjust the height, press the two side buttons on the Skate chassis and simultaneously move the Skate-seat up or down until they click into place. To make sure that the Skate-seat is secured, check the 3 arrows on the Skate chassis.

LEGREST

19•If the Skate seat is in the carriage position, the leg rest must stay in the reclined (flat) position. If the Skate seat is in the stroller seat position, the leg rest can be adjusted to 2 positions (reclined or upright).

20•To adjust it, pull the side adjuster traps and place over the side pins. Pull the additional loose strap under the stroller seat and attach it to the Velcro on the bottom of the seat.

BACKREST

21•The backrest can be set in 3 positions: horizontal, partially raised, and raised.

To adjust the backrest, take the central strap and place one of the 3 eyelets on the pin behind the backrest.

BUMPER BAR/CARRYING HANDLE

22•To attach it, place the fasteners of the bumper bar on the Skate-seat side buttons, push the buttons down and slide the bumper bar into the groves until it snaps in. The bumper bar can be attached to the Skate-seat in one way only.

23•To remove it, press the button below the bumper bar and slide out of the groves.

24•The bumper bar can be opened and closed: to make it easier for the child to go in and out of the stroller when he/she is older.

To open it: press the two round buttons simultaneously and pull the bumper bar outwards. To close it: follow these steps the other way round.

25•The bumper bar can be adjusted to 2 positions: position (A) – bumper bar mode – and position

(B) – carrying handle mode, to carry a child up to 9 kg (19.8 Ibs) only when the Skate-seat is used as a carriage.

•To adjust it in height: open the two levers inward, move the bumper bar up or down and close the two levers again.

DETACHING THE Skate-SEAT FROM THE Skate

CHASSIS

26•Raise the bumper bar to the up position (carrying handlebar), hold it and pull it upwards (1), detach the Skate-seat on one side (2) then on the other

(3) by pressing the tabs where the hood attaches.

•IMPORTANT: when the child is seated, this operation can be carried out only if the Skate seat is in carriage mode and your child weighs less than 9 kg (19.8 Ibs).

REVERSIBLE Skate-SEAT

•The Skate-seat is reversible, so it can be attached to the Skate chassis to face parents or let your

child see what’s ahead.

27•Skate carriage seat: must be fixed to the Skate chassis so it faces parents to keep a constant eye on your little baby.

28•Skate stroller seat: can be fixed to the Skate chassis so the baby can face parents (1) or see what's ahead (2).

HOOD

29•To mount the hood, insert the hood fasteners into the proper holes of the Skate seat with the snaps to the rear of the stroller seat, then fasten all 4 snaps on the Skate seat.

30•To remove it, unsnap the hood from the side Skate seat, press in the thin black buttons under the grey tabs and pull the hood off.

31•The hood can also be extended for use in the carriage mode by unzipping the zipper on the outside of the hood.

BOOT

32•To place the boot on the Skate seat, fasten the two snaps at the bottom of the Skate seat and put the elastic strings onto the two side pins on the bumper bar. The boot also has side magnets to help secure it to the Skate seat. When using the boot in the carriage position you can unzip the boot to allow more room for your children’s feet.

RAIN COVER

33•To attach it, zip the rain cover and the hood together (A), pull the bottom part of the rain cover under the Skate-seat (B), pass the elastic strings and buttons behind the locking system of the Skate-seat (C), then button them up to the rain cover (D).

•The rain cover can be opened while attached to the Skate-seat due to the elastic strings, but the zipper must be open.

•If you want to turn the Skate-seat, you do not need to remove the rain cover as it is attached to the Skate-seat and not to the Skate chassis.

•Do not use the rain cover in closed environments and always make sure the child is not too hot.

•Do not place the rain cover near heat sources and be careful with cigarettes.

•Check that the rain cover does not hinder the correct functioning of the carriage or stroller.

•Always remove the rain cover before closing your carriage or stroller.

•Wash with a sponge and soap water, without using detergents.

5 POINT HARNESS SAFETY BELT

34•Safety belts are stored under the interior Skate- seat padding in their proper housings.

35•The seat belt is hidden under the interior Skate-seat padding: From the carriage position to access the safety belts, you need to unsnap the 4 snaps where the backrest meets the bottom of the seat. Pull up the seat pad and pull the shoulder harness out. Next slide the crotch strap thru the slit in the seat pad.

Page 16 Page 18
Page 17
Image 17
Peg-Perego SKATE Legrest, Backrest, Bumper BAR/CARRYING Handle, Chassis, Hood, Boot, Rain Cover, Point Harness Safety Belt
Page 16 Page 18

SKATE specifications

The Peg-Perego SKATE is a remarkable stroller designed to cater to the needs of modern families, combining convenience, versatility, and style. This innovative stroller is perfect for parents who want an adaptable solution that grows with their child, and it makes navigating both urban and suburban landscapes a breeze.

One of the standout features of the Peg-Perego SKATE is its modular design. It allows for multiple configurations, accommodating infants and toddlers with ease. The stroller can be used with a car seat, bassinet, or as a traditional stroller seat, ensuring that it meets the needs of your growing child. The compatibility with Peg-Perego's Primo Viaggio car seat makes it a seamless travel system, providing parents with the option to transition from car to stroller without having to disturb their little ones.

Stability and maneuverability are hallmarks of the SKATE. Its larger rear wheels and front swivel wheels ensure smooth handling on various terrains, whether you are on a busy city sidewalk or navigating a bumpy park path. The adjustable handlebars cater to parents of different heights, making it comfortable for everyone to push.

Safety and comfort are prioritized in the design of the Peg-Perego SKATE. The stroller features a multi-position reclining seat that allows your child to sit up straight or lean back for a nap. Additionally, it is equipped with a five-point harness system, providing security for your child during your outings. The large canopy offers ample sun protection, shielding your little one from harmful UV rays while still allowing for ventilation.

Convenience extends to the SKATE's storage options as well. It comes with a generous shopping basket beneath the seat, enabling parents to carry diaper bags, groceries, or other essentials. The stroller also features a compact fold mechanism, making it easy to store and transport.

Furthermore, Peg-Perego emphasizes quality craftsmanship, with the SKATE being made in Italy using high-quality materials that ensure durability and longevity. Its stylish design does not compromise functionality, making it a fashionable yet practical choice for stylish parents.

In summary, the Peg-Perego SKATE is a versatile stroller packed with features that cater to the safety, comfort, and convenience of both parents and children. Its adaptability, stability, safety features, and stylish aesthetics make it an excellent choice for families on the go.
Top Page Image Contents