Pelco C1555M-F, C1566M-C, C1572M MOUNTING

10 C1555M-F (10/05)

MOUNTING

Install the System 9770 in EIA-standard 19-inch (48.26 cm) racks.

CM9770-MXB

1. Install the CM9770-MXB mounting bafﬂe ﬁrst (refer to Figure 1).

The mounting bafﬂe uses 1 rack unit (RU), and it has front and rear mounting ears, which are attached to the front and rear mounting racks.

The rear mounting brackets are adjustable to allow for different depths of cabinets.

The mounting bafﬂe provides the following functions:

• The mounting bafﬂe helps to direct the heat from a lower matrix bay (or other equipment) toward the rear of the mounting bafﬂe,

instead of allowing the heat to ﬂow up into the matrix bay.

• The mounting bafﬂe supports the weight of the matrix bay.

• The matrix bay is easier to install when it is sitting on top of the mounting bafﬂe.

Figure 1.

CM9770-MXB Mounting Bafﬂe

2. Install the CM9770-MXB matrix bay on top of the mounting bafﬂe. Refer to Figure 2.

In a single-bay installation, always leave 1 RU of space above the matrix bay for airﬂow.

In a multiple-bay installation you do not need to leave additional RUs open between units. However, you must always leave 1 RU of space

above the upper bay.

NOTE:

Be sure to use all eight screws provided with the mounting bafﬂe. The mounting bafﬂe must be installed securely to support the

weight of the matrix bay.

NOTE:

Figure 2 illustrates the recommended mounting method. For an alternate, open-rack mounting method, refer to the

Mounting the

CM9770-MXB in an Open Rack

section in the

Appendix

.

Contents

Main ADDENDUM Page Page Contents List of Illustrations List of Tables Description MODELS Controller and CPU Components Network Interface Unit Matrix Bay Keyboards Compatible Receivers Optional Components Installation UNPACKING MOUNTING Page Page VIDEO INPUT/OUTPUT CONNECTIONS Opening the CM9770-MXB Front Cover Installation Tips INSTALLING VIDEO INPUT CARDS (CM9770-VCC) Remove a Video Card Insert or Replace a Video Card How to Turn On the Pelco V-Sync Signal INSTALLING MONITOR OUTPUT CARDS (CM9770-VMC) Remove a Monitor Card Insert or Replace a Monitor Card PERFORMING A BASIC LED CHECK INSTALLING REAR PANEL BNC CARDS Remove a Rear Panel Video BNC Card (CM9770-RPC) Insert or Replace a Rear Panel Video BNC Card (CM9770-RPC) Change the Termination Jumpers on a Rear Panel Video BNC Card Looping Video Insert or Replace a Rear Panel Monitor BNC Card (CM9770-RPM) VIDEO INPUT/OUTPUT CAPACITY Single Bay .................. Multiple Bays, Single Node C1555M-F (10/05) 23 Figure 14. Sample Sideframing System Using an Output Bay Page Networked System THE POWER SUPPLY MODULE (CM9700-MPS) REMOVE A BACKUP POWER SUPPLY INSTALL A BACKUP POWER SUPPLY HOW TO REPLACE THE FUSE IN A POWER SUPPLY MODULE HOW TO TURN OFF THE AUDIBLE POWER SUPPLY ALARM SYSTEM DEVICE CONNECTIONS Page RS-422 COM PORT (SERCOM) CONNECTIONS Page C1555M-F (10/05) 33 Figure 23. Sample CM9770-MXB to CM9700-CC1 Connection Figure 24. Sample CM9770-MXB and CM9700-CC1 Connections in a Networked System System Start-Up INITIALIZE THE CC1 VERIFY SYSTEM OPERATION INITIALIZE KEYBOARDS DISPLAY THE CM9770-MXB SOFTWARE VERSION LEVEL DISPLAY A BLUE RASTER SCREEN MONITOR COLOR ADJUSTMENT Programming Your System GETTING HELP USING CM9700-MGR Operation OPERATING YOUR SYSTEM 9770 Switch Monitors Select Cameras Control Receivers Appendix SYSTEM ARCHITECTURE HOW TO EXPAND YOUR SYSTEM INSTALLING ADDITIONAL MATRIX BAYSSIDEFRAMING AND DOWNFRAMING Sideframing Downframing Page Downframe Cards C1555M-F (10/05) 45 Figure 34. DFC Card Figure 35. CM9770-DFL Card HOW TO INSTALL OR REPLACE A CM9700-SER CARD IN THE CC1 Figure 38. How to Install a CM9700-SER Card W2 ADDRESS SELECT W1 IRQ SELECT VIDEO INPUT CARD (CM9770-VCC) DETAIL MONITOR OUTPUT CARD (CM9770-VMC) DETAIL Page NETWORKING CONNECTING SATELLITE DEVICES PROGRAMMING SATELLITE DEVICES HOW TO INSTALL VIDEO PATCH PANELS (CM9700-VPP) Page DOS ENVIRONMENT AND COMMAND REFERENCE THE BOOT PROCESS AUTOEXEC.BAT AND THE BOOT PROCESS Invoking the CM9700 Executable File Names and DOS DOS Commands The Path Statement Navigating the DOS Directory Tree Manipulating Files in the DOS Environment Using the Wild Card Character DOS REFERENCE Page Troubleshooting Problems with the CC1 The VCC Card CF LED Is Illuminated and the AUX LED Is Blinking Monitor Display Problems LED Indicators on the Power Supply Module Specications Page Regulatory Notices CM9780-MXB PRODUCT WARRANTY AND RETURN INFORMATION REVISION HISTORY