Pelco PV130 RS-422 RS-422 Circuit PV130, Wiring Diagram, Warranty And Return Information

Testing (Refer to PV1000 Instruction/Operation Manual)

1.Ensure that the PV1016 Transmitter DIP switch settings or the PV1004 Transmitter programming are correct for the telemetry type required by the receiver.

2.Ensure that the PV1000 Transmitter is properly programmed for the COM 2 port baud rate and parity required by the receiver.

3.Confirm receiver PTZ control from a PV1016 Transmitter with front panel keyboard (while off-line) or from the PV1016 Receiver (while on-line). Check for smooth operation.

Common Causes for Control Problems

No Control
	• Converter-to-receiver twisted pair connections reversed or
• Transmitter DIP switch settings or programming incorrect for
receiver type.	wired incorrectly.
• Transmitter COM 2 port baud rate and/or parity programming	• Power supply +12 VDC and GND connections to converter
incompatible with receiver type.	reversed.
Erratic Control
• Cabling between converter and receiver incompatible with	• Wire distance between converter and receiver exceeds
RS-422 operation.	4,000 feet.
• Wire distance between converter and receiver requires suitable	• Video coax cable has Coaxitron® or other “up-the-coax”
termination at receiver.	control information present.

Figure 2. RS-422 Circuit PV130	RS-422
Wiring Diagram
TX-		RX-
TX+		RX+
RX-		TX-
RX+		TX+
GND		GND
100	100

WARRANTY AND RETURN INFORMATION

WARRANTY	The above warranty provides the Dealer with specific legal rights. The Dealer may
Pelco will repair or replace, without charge, any merchandise proved defective in	also have additional rights, which are subject to variation from state to state.
material or workmanship for a period of one year after the date of shipment. Excep-
tions to this warranty are as noted below:	If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
	(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the
• Three years on Genex® Series (multiplexers, server, and keyboard).	following information:
• Two years on cameras and all standard motorized or fixed focal length lenses.
• Two years on Legacy®, Camclosure™ Camera Systems, CM6700/CM8500/	1. Model and serial number
CM9500/CM9750/CM9760 Matrix, PelcoVision®, DF5 Series and DF8 Fixed Dome	2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
products.	3. Details of the defect or problem
• Two years on Spectra® and Esprit™, including when used in continuous motion
applications.	If there is a dispute regarding the warranty of a product which does not fall under the
• Two years on WW5700 series window wiper (excluding wiper blades).	warranty conditions stated above, please include a written explanation with the
• Six months on all pan and tilts, scanners or preset lenses used in continuous	product when returned.
motion applications (that is, preset scan, tour and auto scan modes).
	Method of return shipment shall be the same or equal to the method by which the
Pelco will warrant all replacement parts and repairs for 90 days from the date of	item was received by Pelco.
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to	RETURNS
Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration,
normal wear, or accident are not covered under this warranty.	In order to expedite parts returned to the factory for repair or credit, please call the
	factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA
Pelco assumes no risk and shall be subject to no liability for damages or loss result-	number if returned for credit, and RA number if returned for repair). Goods returned
ing from the specific use or application made of the Products. Pelco’s liability for any	for repair or credit should be clearly identified with the assigned CA/RA number and
claim, whether based on breach of contract, negligence, infringement of any rights	freight should be prepaid. All merchandise returned for credit may be subject to a
of any party or product liability, relating to the Products shall not exceed the price	20% restocking and refurbishing charge.
paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any
special, incidental or consequential damages (including loss of use, loss of profit	Ship freight prepaid to: Pelco
and claims of third parties) however caused, whether by the negligence of Pelco or	3500 Pelco Way
otherwise.	Clovis, CA 93612-5699

REVISION HISTORY

Manual #	Date	Comments
C1919M	9/97	Original version.
C1919M-A	3/00	Revised installation instructions and Figure 1. Added Figure 2.
C1919M-B	7/00	Corrected RX polarity in Figure 1.
C1919M-C	11/00	Revised drawings to reflect label change.

® Pelco, the Pelco logo, Spectra, Genex, Legacy, Coaxitron, and PelcoVision are registered trademarks of Pelco.	© Copyright 2000, Pelco.
™ Esprit and Camclosure are trademarks of Pelco.	All rights reserved.