TrackerTM 2140

OPERATING INSTRUCTIONS CAT. #2140C

Battery Installation

To install the batteries:

1.Remove the lens cover and pull out the lamp module.

2.Install two (2) AAA alkaline batteries-one with the positive end facing upward, the other with the positive end facing downward.

3.Insert the lamp module by lining up the slot on the module side with the rib inside the body, then slide the module into the flashlight.

4.Replace the lens cover.

Turn On/Off

1.To turn ON: turn lens cover clockwise until lamp lights.

2.To turn OFF: turn lens cover counter clockwise until lamp turns off, then continue to turn at least one full turn.

Lamp Replacement

To replace the lamp module:

1.Remove the lens cover and pull out the burnt-out lamp module.

2.Insert the new lamp module by lining up the slot in the module with the rib inside the body, then slide the module into the flashlight.

3.Replace the lens cover.

Hydrogen Gas Absorber Pellets

Located inside the flashlight are catalyst pellets which are present to absorb hydrogen gas that could possibly be emitted by defective, leaking, reversed polarity or heavily discharged batteries.

If the pellets become wet, let them air dry. Pelican Products assumes no liability for any brand batteries which are defective or cause injury to anyone when used in any Pelican flashlight.

O-Ring Maintenance

The TrackerTM flashlight uses an o-ring seal to pre- vent water from entering the battery compartment. It is a good idea to occasionally lightly grease the o-ring with a silicone lubricant to prevent leakage.

PRODUCT SPECIFICATIONS

Lamp Type:

Xenon

Battery Type:

E92 1.5V Alkaline AAA-cell (2)

REPLACEMENT PARTS

CAT. #

DESCRIPTION

2301

0-ring

2144

Lamp Module

CAUTION:

If light is not to be used for some time, remove batteries to prevent possible leakage and corrosion.

Battery Safety Bulletin

Alkaline Batteries

1.Hazardous location safety approvals for explosive environments are only valid for the specified cell type manufacturer and, where applicable, brand names that are displayed on the flashlight and/or instructions sheets that are supplied with the light.

2.The use of other battery technologies may reduce the performance of the the flashlight. Always read the battery manufacturers recommendations for the appropriate use of the battery technology/brand prior to using them in the flashlight.

3.When replacing the batteries:

a.Replace all the batteries at the same time.

b.Do not mix battery brands and old and new batteries.

c.Always insert batteries correctly with regard to polarity (+ and -) marked on the battery and equipment.

4.Do not change batteries in a hazardous location.

5.Remove batteries from equipment if it is not to be used for an extended period of time.

TrackerTM 2140

INSTRUCCIONES DE FUNCIONAMIENTO

CAT. #2140C

Instalación de pilas

Para instalar las pilas:

1.Retire la tapa de el lente y quite el módulo de la bombilla.

2.Instale dos (2) pilas alcalinas tipo AAA, una con el polo positivo hacia arriba, la otra con el polo positivo hacia abajo.

3.Inserte el módulo de la bombilla alineando la ranura ubicada a un costado del módulo con el reborde del cuerpo de la linterna, y luego deslice el módulo dentro de la linterna.

4.Vuelva a colocar la tapa de el lente.

Encendido/apagado

1.Para encender: Gire la tapa de el lente en sentido horario hasta que se encienda la bombilla.

2.Para apagar: Gire la tapa de el lente en sentido contra horario hasta que se apague la bombilla y luego continúe girando por lo menos una vuelta completa.

Reemplazo de la bombilla

Para reemplazar el módulo de bombilla:

1.Retire la tapa de el lente y quite el módulo de bombilla quemado.

2.Inserte el nuevo módulo de bombilla, alineando la ranura ubicada a un costado del módulo con el reborde del cuerpo de la linterna, y luego deslice el módulo dentro de la linterna.

3.Vuelva a colocar la tapa de el lente.

Mantenimiento de la junta tórica

La linterna TrackerTM utiliza una junta tórica de sellado para impedir que entre agua en el compartimento de las pilas. Es conveniente engrasar la junta levemente con un lubricante de silicona para impedir la filtración de agua.

ATENCION

Si no se piensa utilizar la linterna durante algún tiempo, quite las pilas para impedir cualquier fuga o corrosión.

ESPECIFICACIONES DEL PRODUCTO Tipo de bombilla: Xenon

Tipo de pila: E92 Alcalina de 1,5V tipo AAA-cell

PIEZAS DE REPUESTO

 

2301

Junta tórica

2144

Módulo de bombilla

23215 Early Ave. • Torrance, CA 90505 USA Tel (310) 326-4700 • FAX (310) 326-3311 www.pelican.com

PELICAN CANADA

10221-184 St. • Edmonton, Alberta T5S 2J4 Tel (780) 481-6076 • FAX (780) 481-9586

PELI PRODUCTS, S.L.U.

c/ Provença, 388, Planta 7 • 08025 • Barcelona, Spain

Tel: +34 934 674 999 • Fax: +34 934 877 393

2143-311-000 5-2434 Rev B SP/11

© 2011 PELICAN PRODUCTS

All trademarks and logos displayed herein are registered and unregistered trademarks of Pelican Products, Inc. and others.

Energizer is a registered trademark of Eveready Battery Company, Inc.

PELICANTM

TrackerTM 2140

CAT. #2140C

23215 Early Ave. • Torrance, CA 90505 USA Tel (310) 326-4700 • FAX (310) 326-3311 www.pelican.com

Page 2
Page 1
Image 1
Pelican 2140C specifications Battery Installation, Turn On/Off, Lamp Replacement, Ring Maintenance, Encendido/apagado
Page 2

2140C, 2140 specifications

The Pelican 2140 and 2140C are part of Pelican Products' renowned line of portable lighting solutions, designed to provide reliable illumination in various challenging environments. Built with robust features, these compact flashlights ensure performance and durability, making them popular choices for professionals and outdoor enthusiasts alike.

One of the standout features of the Pelican 2140 series is its exceptional brightness. The LED light produces an impressive output, delivering up to 190 lumens, which is more than sufficient for a range of tasks, from routine maintenance to emergency situations. The 2140 model is equipped with a powerful white LED, while the 2140C includes a color filter, offering versatility in lighting options for specific applications.

Durability is a hallmark of Pelican’s products, and the 2140 series is no exception. Constructed with a high-impact polymer body, these flashlights are resistant to extreme conditions, including impacts, water, and dust. The pelican 2140 is also IPX4 rated, ensuring splash resistance, making it a reliable choice for outdoor use and in demanding conditions.

The ergonomic design of the Pelican 2140 series enhances user experience. Its lightweight construction allows for easy handling and portability, while a thoughtful grip ensures comfortable use over extended periods. They also feature a sturdy clip that enables attachment to belts or pockets, providing hands-free convenience.

Furthermore, the 2140 and 2140C models feature a tactical switch that allows for quick and easy access to the light. This functionality is especially valuable in emergencies when every second counts. The lights also come equipped with a 120-degree beam angle, ensuring wide illumination coverage.

Battery life is another crucial aspect of the Pelican 2140 series. These flashlights are powered by two AA alkaline batteries, providing extended use without the need for frequent replacements. The energy-efficient LED technology enhances battery longevity, making these lights ideal for professionals needing reliable illumination over long periods.

In summary, the Pelican 2140 and 2140C models encapsulate the brand’s commitment to quality, performance, and user-centric design. With high brightness levels, durable construction, handy features, and excellent battery life, they are well-suited for various applications, from tactical operations to outdoor adventures and everyday tasks. Whether you are a first responder, a construction worker, or simply someone who appreciates reliable lighting, the Pelican 2140 series is an outstanding choice that will not disappoint.
Top Page Image Contents