BATTERY INSTALLATION
1.Remove lens housing by turning counter- clockwise.
2.Remove the lamp and contact module.
3.Remove used batteries and replace with fresh batteries as shown on the outside of the engraved body.
4.Replace the contact module and lamp.
5.Replace lens housing squarely on threads and turn clockwise while pressing on the lens hous- ing slightly.
ON/OFF
Swing the switch lever to the right (light facing away from you) until light activates. To turn light off, swing the switch lever to the left (light facing away from you) until light goes off.
WARNING – Explosion Hazard - Batteries must only be changed in
WARNING –
Explosion Hazard - Substitution of components may impair suitability for use in hazardous locations
CAUTION:
If light is not to be used for some time, remove batteries to prevent possible leakage and corrosion.
Battery Replacement
Do not mix battery brands or use Nicad or Zinc Carbon Batteries. Do not mix old and new batteries. Replace all batteries at the same time.
Lamp Replacement
Lamp replacement may only be performed in a
DO NOT MODIFY THIS PRODUCT!
WARRANTY RETURN POLICY
Send all items for repair or replacement directly to Pelican Products Customer Service Department (postage paid). Please call for a return authorization number. Per our guarantee, Pelican Products will replace or repair any broken or defective products. Upon receipt of goods, Pelican Products will notify you of any handling and return postage charges.
If your local retailer does not stock the above acces- sory parts, you may order them directly from Pelican Products. Send check or money order in U.S. dol- lars, or order by phone using MasterCard or VISA (ask for Customer Service). SORRY, NO C.O.D.’s. Subject to sales tax. Allow
LAMP REPLACEMENT
1.Remove lens housing by turning
2.Remove the lamp and contact module.
3.Replace the contact module and lamp.
4.Replace lens housing squarely on threads and turn clockwise while pressing on the lens housing slightly.
PRODUCT SPECIFICATIONS
Lamp Type: | Xenon |
Battery Type: | 4 AA Cell Alkaline (Included) |
Battery Brand: | Eveready® Energizer® |
REPLACEMENT PARTS | |
CAT # | DESCRIPTION |
2401 | |
2404 | LAMP MODULE |
CAUTION: Read This Notice Before Use.
Hydrogen Gas Absorber Pellets
Located inside the flashlight are catalyst pellets which are present to absorb hydrogen gas that could possibly be emitted by defective, leaking, reversed polarity or heavily discharged batteries. If the pellets become wet, let them air dry. Pelican Products assumes no liability for any brand batteries which are defective or cause injury to anyone when used in any Pelican flashlight.
WARNING! static hazard - clean only with a damp cloth
PELICAN LEGENDARY LIFETIME
GUARANTEE OF EXCELLENCE Pelican Products, Inc. guarantees its products for a lifetime against breakage or defects in workmanship. This guarantee does not cover the lamp or batteries (rechargeable or alkaline). Any liability, either expressed or implied, is limited to replacement of the product. This guarantee is void if the Pelican product has been abused beyond normal and sensible use.
This guarantee does not cover shark bite, bear attack or damage caused by children under five.
Lifetime Guarantee does not cover Roto Molded or AALG products. Refer to www.pelican.com/warranty for full details.
PELICANTM
StealthLiteTM 2400
Cat. #2400
SUBMERSIBLE
23215 Early Ave. • Torrance, CA 90505 USA Tel (310)
PELICAN TM CANADA
Tel (780)
PELITM PRODUCTS, S.L.U.
c/ Casp,
Tel (+34) 93.467.4999 • FAX (+34) 93.487.739 • www.peli.com
StealthLiteTM 2400
Cat. #2400
INSTRUCCIONES DE FUNCIONAMIENTO
INSTALACION DE LAS PILAS
1.Retire el bastidor de la lente girándolo en sentido contrario de las agujas del reloj.
2.Retire el módulo de la bombilla y el contacto.
3.Saque las pilas gastadas y sustitúyalas por pilas nuevas tal y como se indica en la parte exterior del cuerpo de la linterna.
4.Vuelva a colocar el módulo de la bombilla y el contacto.
5.Vuelva a colocar el bastidor de la lente sobre la rosca y gire en el sentido de las agujas del reloj al mismo tiempo que ejerce un poco de presión sobre el mismo.
ENCENDIDO / APAGADO
Para encender la linterna (con el extremo de la bombilla apuntando en la dirección opuesta a usted), gire la palanca del interruptor hacia la derecha hasta que se encienda. Para apagarla, gire la palanca del interrup- tor hacia la izquierda (con el extremo de la bombilla apuntando en la dirección opuesta a usted), hasta que se apague.
Advertencia - Peligro de explosión - La sustitución de componentes puede afectar a la idoneidad de su uso en zonas potencialmente explosivas.
23215 Early Ave. • Torrance, CA 90505 USA Tel (310)
PELICANTM CANADA
Tel (780)
PELITM PRODUCTS, S.L.U.
c/ Casp,
© PELICAN PRODUCTS 2010 2403-311-001 5-0697 Rev A AU/10
All trademarks and logos displayed herein are registered and unregistered trademarks of Pelican Products, Inc. and others.
Eveready and Energizer are registered trademarks of Eveready Battery Company, Inc.
Advertencia - Peligro de explosión - Las baterías sólo deben sustituirse o cargarse en zonas no peli- grosas.
PRECAUCION:
Si no se va a usar la linterna por algún tiempo, retire las pilas para evitar la posibilidad que ocurra una fuga y corrosión.
REEMPLAZO DE LA BOMBILLA
1.Retire el bastidor de la lente girándolo en sentido contrario de las agujas del reloj.
2.Retire el módulo de la bombilla y el contacto.
3.Vuelva a colocar el módulo de la bombilla y el contacto.
4.Vuelva a colocar el bastidor de la lente sobre la rosca y gire en el sentido de las agujas del reloj al mismo tiempo que ejerce un poco de presión sobre el mismo.
ESPECIFICACIONES DEL PRODUCTO
Tipo de bombilla: | Xenón | |
Tipo de pila: |
| 4 AA Cell Alkaline (Included) |
Marca de las pilas: | Energizer® de Eveready® | |
PIEZAS DE REPUESTO | ||
NO. DE CAT. | DESCRIPCION | |
2401 | Junta tórica | |
2404 | Módulo de la bombilla | |
