Philips 17PF9946/37 Hooking UP the Television, Remote Control Batteries, Cable/Cable Box Tv

Connect the open end of the round Cable Company sup- plied cable to the cable signal IN(put) plug on the back of the Cable Box.

Connect the open end of the round Cable Company sup- plied cable to the cable signal IN(put) plug on the back of the Cable Box.

HOOKING UP THE TELEVISION

REMOTE CONTROL BATTERIES

To load the supplied batteries into the remote:

1 Remove the battery compartment door on the back of the remote.

2 After removing the plastic isolation sheet from the battery, place the battery (3V) in the remote. Be sure the (+) and (–) ends of the batteries line up correctly (the inside of the case is marked).

3 Reattach the battery compartment door.

Lithium battery (3V)

Battery Compartment Door

Remote Control
(shown from the bottom)	Be sure to point the
	remote at the remote
	sensor window on the
	front of the television
	when using the remote
	control to operate the
	television

NOTE: The plastic isolation sheet must be removed

for the remote control to function.

CABLE/CABLE BOX TV

Your Cable TV input into your home may be a single (75 ohm) cable or use a cable box decoder. In either case the connec-

tion is very simple. Follow the steps below to connect your cable signal to your new television.

Direct Cable Connections:

This connection will supply Stereo sound to the TV.

1 Connect the open end of the round Cable Company sup- plied cable to the 75Ω input on the bottom of the TV. Screw it down finger tight.

Direct Cable Connection:

Cable signal coming from Cable Company (Round 75Ω coaxial cable)

Jack Panel Bottom of TV

Cable Box (w/RF In/Outputs):

This connection will NOT supply Stereo sound to the TV. The sound from the cable box will be mono.

1

2 Using a separate round coaxial cable, connect one end to the

OUT(put) (TO TV) plug on the back of the Cable Box.

3 Connect the other end of the round coaxial cable to the 75Ω input on the bottom of the television. Screw it down fin- ger tight.

NOTE: Be sure to set the OUTPUT CHANNEL SWITCH on the back of the cable box to CH 3 or 4, then tune the cable box on the TV to the corresponding channel. Once tuned, change channels at the cable box, not the television.

Cable Box with RF Inputs and Outputs Connection:

Output Channel Switch

Cable Signal

IN from the

Cable

Company

Round 75Ω

Coaxial Cable

Jack Panel Bottom of TV

Jack Panel Back

of Cable Box

Cable Box (w/Audio/Video Outputs):

This connection will supply Stereo sound to the TV.

1

2 Using an RCA type Video Cable, connect one end of the cable to the Video (yellow) (or ANT, your cable box may be labeled differently) Out jack on the cable box and the other end to the Video end of the composite adapter included with the TV.

3 Using an RCA type Audio Left and Right Cable, connect one end to the left and right Audio Out L & R jacks (red & white) on the cable box. Connect the other ends to the Audio end of the composite adapter cable included with the TV. Connect the adapter into the AV In jack on the bottom of the TV.

NOTE: Use the AV+ button and the Number 1 button on the TV remote control to tune to the AV1 channel for the cable box signal. Once tuned, change channels at the cable box, not the television. Pressing the AV+ button repeatedly will scroll all the AV Input chan- nels, including the presently tuned channel.

Cable Box with Audio/Video Outputs Connection:

Cable Signal IN from the Cable Company

Jack Panel Back

of Cable Box with A/V Outputs

Audio Cables

L & R (Red, White)

Video Cable

(Yellow)

Jack Panel Bottom of TV

ANTENNA TV

Acombination antenna receives normal broadcast chan- nels (VHF 2–13 and UHF 14–69). Your connection is easy because there is only one 75Ω (ohm) antenna plug on

the back of your TV, and that’s where the antenna goes.

1 If your antenna has a round cable (75 ohm) on the end, then you're ready to connect it to the TV.

If your antenna has flat, twin-lead wire (300 ohm), you first need to attach the antenna wires to the screws on a 300- to 75-ohm adapter.

2 Push the round end of the adapter (or antenna) onto the 75Ω (ohm) plug on the bottom of the TV. If the round end of the antenna wire is threaded, screw it down finger tight.

Antenna Connection:

Outdoor or Indoor Antenna	300 to 75-ohm
(Combination VHF/UHF)	Adapter
The combination antenna
receives normal
broadcast channels 2-13 (VHF)
and 14-69 (UHF).
	Twin
	Lead Wire

Round 75Ω

Coaxial Cable

from Antenna

2

Jack Panel

Bottom of TV