USINGTHE TV BUTTONS
Should your remote control be lost or broken, you can still
change some of the basic picture and sound settings with the
buttons on the TV. Follow the steps below to familiarize yourself
with the functions of the TV buttons.
1Press POWER/STANDBYto turn the TV on (or off).
Allow about 10 seconds for the TVto power on.
2Press the VOL(ume) + or– buttons to decrease or
increase the sound level.
Press the VOLUME + and – buttons simultaneously to dis-
play the on-screen menu. After the menu appears, use these
buttons to enter submenus and make selections or adjust-
ments. (Use the CHANNELbuttons to move up and down
in the menu or submenus.) Press both VOLUME buttons
simultaneously to back out of the on-screen menus.
3Press SOURCE SELECTto choose from among the sig-
nal inputs you have connected to the TV.
4Press the CHANNELbuttons to select TV channels.
PIP
2
13
5
46
8
79
0
OK
SWAP PIP CH
DN UP
FREEZE
SOUND
VOL CH
MUTE
CC
A/CH
POWER
PICTURE
STATUS/
EXIT
MENU/
SELECT
POSITION
TV
DN UP
123
456
789
0
SURF
A/CH
ACC
VCR
UP
DN
TV/VCR
ACTIVE
CONTROL
TV MODE
Button
TV VCR ACC
OPERATINGTHE TELEVISION AND REMOTE CONTROL
TELEVISION
REMOTE CONTROL
HOOKING UPTHE TV
VIDEO
S-VIDEO
LPb
Pr
VIDEO
S-VIDEO
L
AUDIO
L
R
AUDIO
L
R
G/Y
R/Pr
B/Pb
V
H
SYNC
L
R
AUDIO
L
R
AUDIO
HD INPUT-AV 4
HD INPUT-AV 5
INPUT-AV 2OUTPUTINPUT-AV 1
Y
ANTENNA IN 75Ω
DVI
1
INSTALLING BATTERIES
To load the supplied batteries into the remote, follow these
steps.
1Gently press and hold the indentation on the back of
the remote and slide the battery coveroff the remote.
2Place the two “AA” size batteries in the remote’s bat-
tery case. Ensure that the (+) and (–) ends of the batteries
line up correctly with the (+) and (–) inside the case.
3Slide the battery cover back into place.
POINTINGTHE REMOTE
Press the TVmode button on the remote to ensure that the
remote sends its commands to the TV.When operating the
remote control, point the remote toward the remote sensor win-
dow on the TV.
To prevent battery leakage that
may result in injury to you or dam-
age to the remote control:
• Install ALL batteries correctly, + and –,
as marked on the unit.
• Do not mix batteries (OLD and NEW
or CARBON and ALKALINE, etc.)
• Remove batteries when the remote
control is not used for a long time.
Do not take apart, heat, or put bat-
teries in fire.
Remote Sensor
Window
You can set up your TVremote control to work with accessory
devices such as VCRs, DVD players, and cable converter boxes.
See pages 18–23 in the Directions for Usemanual.
ccCHECK ITOUT
2
BATTERY USAGEC AUTION
• Be sure to point the remote toward the
sensor window on the TVor accessory
device you wish to operate.
• Press the correct mode button for the
device: TV, VCR, ACC (for accessories
other than VCRs).
• Be within about 30 feet (10 meters) of
the TVor accessory device you wish to
operate.
• Avoid dropping the remote on hard sur-
faces.
• Do not use harsh chemicals to clean the
remote. Use only a soft, lightly mois-
tened cloth.
HELPFUL HINTS
SOURCE
SELECT
>
?
+
A
-
A
VOLUME CHANNEL
MENU
SOURCE
SELECT
>
?
+
A
-
A
VOLUME CHANNEL
MENU
Power Standby
Button
You can press any of the buttons on
the front of the TVto turn the TV on,
but you must press the Power/Standby
button to turn the set off.
HELPFUL HINT
TV
SWAPPIP CH
DNUP
FREEZE
SOUND
POWER
PICTURE
STATUS/
EXIT
VCR ACC
MENU/
SELECT
ACTIVE
CONTROL
ANTENNA TV Antenna Signal
This connection WILLsupply stereo sound to the TV.
1Connect the antenna signal to the ANTENNAIN 75Ω
jack on the back of the TV.
NOTE: Refer to the sections on TUNER MODE and AUTO
PROGRAM on pages 4 and 5 of this guide. Set TUNER
MODE to the ANTENNAoption. Run AUTO PROGRAM
to store all available cable channels in the TV’s memory.
Back of TV