CABLE
CABLE / ANTENNA
75
CABLE | HDMI 1 | HDMI 2 |
|
| CABLE / ANTENNA |
| TO TV | 75 |
| 2 | |
IN | OUTPUT | |
OUT |
|
3
STB / SAT
Pr
Pb
CABLE
HDMI 1 | HDMI 2 CABLE / ANTENNA |
75
1 |
SIGNAL | 2 | 4 |
SPLITTER |
|
|
3
IN OUT
STB / SAT
Watching Cable TV programs that don’t require the cable box
Since you’ve connected the cable TV signal directly to the TV’s tuner, you can also watch the unscrambled programs by simply tuning to the desired channel.You must first use Autoprogram, however, to store channels in the TV’s memory. See page 10.
Note:This connection will supply stereo sound to the TV if it is being broadcast by the station you are watching.
&Basic connections to the TV
Your integrated digital TV automatically decodes and displays the four basic DTV picture resolution standards.
-SDTV (Standard Definition TV) are broadcast as 480i
-HDTV
Note: Progressive scan video (p) is more like that you see in a movie theater. Images are much more distinct and free of flicker, and motion is smoother.
Next to analog NTSC broadcast reception, your TV has an integrated High Definition TV tuner which receives, decodes and displays terrestrial ATSC and unscrambled cable (QAM) signals.
HDTV quality is only reproduced when a broadcaster or cable provider broadcasts HDTV signals.
Note: Ask your broadcaster or cable box provider to transmit/enable HD content to your home, and possibly upgrade to a CableCard for the decription of HD signals.
There are 2 ways to get HDTV content: via cable or via antenna.
Note:This drawing is used wherever you can connect cable or antenna.
-Cable TV
Connect the cable TV signal to the CABLE/ANTENNA 75 Ω x jack at the bottom of the TV. See page 10 for details on using Autoprogram to store channels in the TV’s memory.
Note: this connection will supply stereo sound to the TV if it is being broadcast by the station you are watching.
-Cable box with RF IN/OUT
•Connect the incoming cable TV signal to the cable IN jack 1 on the back of the cable box.
•Connect a coaxial cable (not supplied) from the TO TV jack on the back of the cable box to the CABLE/ANTENNA 75 Ω x jack 2 at the bottom of the TV.
Note:Your cable box may have a different label for the TO TV jack, such as
OUTPUT or OUT.
•Set the OUTPUT CH switch 3 of the cable box to CH 3 or 4 (whichever is correct for your cable box), then tune the TV to the corresponding channel.
Once tuned, change channels at the cable box, not the TV.
Note:This connection will not supply stereo sound to the TV. The reason is that the RF output on a cable box - labeled TO TV, OUT or OUTPUT for example - will not send a stereo signal to the tuner (VHF/UHF) input on a TV.
-Cable box with A/V outputs
•Connect the incoming cable TV signal 1 to a signal splitter (not supplied).The signal splitter enables you to avoid having to use the TO TV jack on the back of the cable box.This jack will not supply stereo sound to the TV.
Note:Your cable box may have a different label for the TO TV jack, such as
OUTPUT or OUT.
•Connect a coaxial cable (not supplied) to a connector on the signal splitter and to the CABLE/ANTENNA 75 Ω x jack 2 on the TV.
•Connect another coaxial cable (not supplied) to a connector on the signal splitter and to the cable IN jack 3 on the back of the cable box.
•Connect A/V cables (not supplied) to the VIDEO and AUDIO L and R outputs on the back of the cable box and to the AV2 video (labeled VIDEO) and AUDIO (labeled L and R) jacks 4 behind the door on the back of the TV, see p. 28.
•To view programs from your cable box, first press the AV+ button on the remote control.
•Press the cursor down or up buttons until the AV2 signal source is selected.
•Press the OK button to confirm your selection.The AV2 input source becomes current for the viewing of cable TV programs through your cable box.
Note: If your cable box Audio/Video outputs will not supply video and stereo audio to the TV, you will need to make the connection shown above in the example “Cable box with RF IN/OUT”.
3
