BDL6520EL

By pressing the [PIP ON/OFF] button on the remote control, you can change the mode in the order shown below:

 

 

PIP

 

 

POP

 

 

PBP aspect

 

PBP full

 

Off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The resolutions in the PIP and POP modes are configured as follows:

PIP SIZE

{Small}

: 320

× 240 pixels

 

{Medium} : 480

× 320 pixels

 

{Large} : 640

× 480 pixels

POP SIZE: 474 × 355 pixels

NOTE:

The images displayed in the sub picture always fit the PIP

 

sizes shown above irrespective of the aspect ratio of the input

 

image.

 

 

4.2.5. Configuration1 menu

Panel saving

Choose to enable the panel saving functions and thus reduce the risk of “image persistence” or “ghost-imaging”.

• {Cooling Fan} – Select {On} to turn on the cooling fan all the

time. Select {Auto} to turn on/off the cooling fan according to the

display’s temperature.

NOTES:

• The default {Auto} option will start running the cooling fan

if the temperature of 60°C (140°F) is reached, and will keep

running for 30 minutes after cooling down to the temperature

of 58°C (136°F).

• A temperature-warning message will be shown on the screen if

the temperature reaches 79°C (174°F). All key functions except

[Power] key will then be disabled.

• Once the temperature reaches 80°C (176°F), the display power

will be shut down automatically.

• {Brightness} – Select {On} and the image brightness will be reduced

to an appropriate level.The Brightness setting in the Picture menu

Picture

Screen

Audio

PIP

Configuration1

Configuration2

Advanced option

Switch on state Auto adjust Power save Language Panel saving Color system Network control port Network settings Configuration reset Factory reset

will be unavailable when selected.

• {Pixel shift} – Select the time interval ({Auto} / {10 ~ 900} Seconds

/ {Off}) for the display to slightly expand the image size and shift the

position of pixels in four directions (up, down, left, or right).

Color system

Selects the Color System depending on your input video format.

The options are: {Auto} / {NTSC} / {PAL} / {SECAM} / {4.43NTSC} / {PAL-60}.

NOTE: This item is functional for VIDEO input only.

Network control port

Select the network control port.

Choose from: {RS232} / {LAN(RJ45)} / {Card OPS RS232}.

Switch on state

Select the display status used for the next time you connect the power cord.

{Power off} – The display will remain off when the power cord is connected to a wall outlet.

{Forced on} – The display will turn on when the power cord is connected to a wall outlet.

{Last status} – The display will return to the previous power status (on/off/standby) when removing and replacing the power cord.

Auto adjust

Use this function to automatically optimize the display of VGA input image.

NOTE: This item is functional for VGA input only.

Power save

Use this setting to reduce the power automatically.

{RGB} – Select {On} to let the display enter APM mode when no signal is detected from the HDMI Graphic mode, HDMI, DVI-D, or VGA inputs after 30 seconds.

{VIDEO} – Select {On} to enter power saving mode when no signal is detected from the HDMI Video mode or YPbPr inputs after 30 minutes.

Language

Select the language used in the OSD menu.

The options are: {

} / {

 

} / {

} / {

} /

{

} / {

} / {

} / {

} / {

} / {

}.

NOTES:

If {LAN(RJ45)} is selected, then {RS232} will not be activated, even if a cable is attached, and vice versa.

The option {Card OPS RS232} is functional after connected with your OPS device.

Network settings

Assign {IP address}, {Subnet Mask}, and {Default gateway} for the display.

Network settings

Network host name

 

9

 

0

Z

L

 

 

 

DHCP

 

 

 

 

Disable

 

 

 

IP address

172

-

16

-

0

-

1

Subnet mask

255

-

255

-

0

-

0

Default gateway

0

 

-

0

-

0

-

0

Login user name

 

a

d

m i

n

 

 

 

Login password

0

 

0

0

 

0

 

 

 

[ SET ]

 

 

 

 

 

 

change [SET] in STORE

DHCP – Choose to enable or disable the DHCP function. If enabled, the display will be assigned IP address, Subnet mask and Default gateway automatically. If disabled, you will be prompted

17

Page 25
Image 25
Philips BDL6520 user manual Configuration1 menu