Philips DVD763SA/051, DVD763SA/001, DVD763SA/021 manual Display PWB Nuclei Error Code Error text

EN 38 5. DVD763SA Diagnostic Software, Trouble Shooting and Test Instructions

Error
code	Error text
5820	Test successful
5840	Test successful
5860	Test successful
5801	"Unexpected response from Basic Engine"
7000	"Manuf. ID: <XX>" "Device ID: <YY>"
7001	"Comm Test Failed"
7002	"Load Cmd Failed"
7003	"Load Dat Failed"
7004	"Run Cmd Failed"
7100	"ROM Checksum: XXXX"
7101	"Comm Test Failed"
7102	"Load Cmd Failed"
7103	"Load Dat Failed"
7104	"Run Cmd Failed"
7201	"Comm Test Failed"
7200	"Test successful"
7202	"Load Cmd Failed"
7203	"Load Dat Failed"
7204	"Run Cmd Failed"
7205	"Scratch circuit not OK"

5.8.3Display PWB Nuclei

Error
code	Error text
3000	“Test successful”
3001	“Disp not responding”
3002	“Disp key no response”
3003	“One or more patterns not correct”
3004	“Disp type invalid”
3020	“Test successful”
3021	“Disp not responding”
3022	“Disp key no response”
3023	“One or more patterns not correct”
3040	“Test successful”
3041	“Disp not responding”
3042	“Disp key no response”
3043	“One or more patterns not correct”
2700	“Model name in wich the test is running”
2701	“Disp key no response”
2702	“Disp not responding”
2707	“Stop key not pressed”
2708	“Pause key not pressed”
2709	“Play key not pressed”
2710	“Open/close key not pressed”
2713	“Previous key not pressed”
2714	“Next key not pressed”
2715	“More than one key not pressed”
2716	" Audio key not pressed"
2900	“Test successful”
2901	“Slave not responding”
2902	“Slave keyboard not responding”
2903	“Standby led not working”
2800	“Test successful”
2801	“Slave display controller not responding”
2802	“Slave keyboard not responding”
2803	“No key press received from remote control”

Error
code	Error text
2600	“The ROM version of the slave processor =
	0xXX, and the internal ID = 0xYY”
2601	“I2c bus busy”
2602	“I2c bus not working“
6000	P50 test
6001	“No readback on P50”
6002	“Disp not responding “
6003	“P50 readback error”

5.8.4Processor & Peripherals Nuclei

Error
code	Error text
700	Test successful
720	Test successful
740	Test successful
600	"All checksums are correct"
601	“Following checksum is faulty: BootCode1
	Checksum is 0xY2 and is not correct (must be
	0xZ2)”
601	“This test is not available when stand-alone
	compiled”
6200	"Checksums = 0xA1, 0xB1, 0xC1, 0xD1"
6201	“This test is not available when stand-alone
	compiled”
1000	Test successful
1001	Test successful
1020	Test successful
1021	Test successful
1100	Test successful
1104	“NVRAM reply time-out”
1200	Test successful
1202	“Slave bus not working”
1203	“Slave controller not responding”
1204	“Slave response is not correct”
5900	Test successful
5901	“I2c bus busy”
5902	“I2c bus not working“
5904	“DTS chip response not correct”
1300	Test successful
1301	“Parity error from basic engine to serial”
1302	“Parity error from serial to basic engine”
1303	“No communication between serial and basic
	engine”
1304	“Communication time-out error”
1600	Test successful
1601	“The DVD SDRAM is faulty”