Philips FW-C72 manual Selecting a desired track, Programming Tracks, Reviewing the program

16 CD

•If you wish to change the inner disc during playback, press DISC CHANGE again.

ª“DISC CHANGE" will be displayed.

ªThe CD will stop playing.

ªThe CD carousel tray will close to

retrieve the inner CD and then open again with the inner CD accessible.

3Press OPEN•CLOSE to close the CD carousel tray.

Selecting a desired track

Selecting a desired track when playback is stopped

1Press ’ or ‘ until the desired track appears on the display.

2Pressƒ to start playback.

ªThe selected track number and elapsed playing time appear on the display.

Selecting a desired track during playback

•Press ’ or ‘ until the desired track appears on the display.

ªThe selected track number and elapsed playing time appear on the display.

•If you press ’ once it will skip to the beginning of the current track and play the track again.

Note:

–Pressing’ during shuffling can only skip to the beginning of the current track.

Searching for a particular passage during playback

•Press and hold ˆ or ‡ until the desired passage is located.

ª The volume will be reduced.

•Play returns to normal when ˆ or

‡ is released.

Programming Tracks

Programming tracks of a loaded CD is possible when playback is stopped.The display will indicate the total tracks stored in the program. Up to 40 tracks can be stored in the memory in any order.When 40 tracks are stored and you attempt to store another track, the display will show “FULL”.

1Load the desired discs in the disc trays.

2Press PROG to start programming.

ªThe PROGRAM starts flashing.

ªIt will cancel any previously selected repeat mode.

3Press the CD (CD 1•2•3) or DISC 1/2/3 button to select the disc.

4Press ’ or ‘ to select the desired track.

5Press PROG to store the track.

•Repeat steps 3 to 5 to store other discs and tracks.

6Press ‚ once to end programming.

ªThe total number of tracks programmed and total playing time appear on the display.

Notes:

–If the total playing time is more than “99:59“ or if one of the programmed tracks has a number greater than 30, then “--:--” appears on the display instead of the total playing time.

–If the system is reading the disc, programming is not possible, “READING” will be displayed and followed by "DISC X" "X" is the current read disc number.

–During programming, if no button is pressed within 20 seconds, the system will exit program mode automatically.

Reviewing the program

Reviewing of the program is possible only when playback is stopped.

•Press ’ or ‘ repeatedly to review the programmed tracks.

•Press ‚ once to exit review mode.

Playing the program

1Press ƒ to start program playback.

ª“PLAY PROGRAM” will be displayed.

ªThe track number and elapsed playing time of the current track will appear on the display.

•If you press REPEAT during program playback, the current track or all programmed tracks will be played repeatedly.

ª“TRACK” or "PROGRAM" will be displayed.

ªThe REPEAT and PROGRAM appear

on the display.

2Press ‚ to stop program playback.

Notes:

–If you press any of the CD DIRECT PLAY buttons, the system will play the selected disc or track and the stored program will be ignored temporarily. The PROGRAM display also will disappear temporarily from the display. It will reappear when playback of the selected disc ends.

–REPEAT DISC mode will be cancelled when program playback begins.

Erasing the program (when

playback is stopped)

•Press ‚.

ª“PROGRAM CLEARED” will be displayed.

Note:

–The program will be erased when the system is disconnected from the power supply or when the CD carousel tray is opened.

pg 01-27/C71-C72/37-Eng 16 12/16/99, 1:20 PM 3139 116 19521 (ENG)