Philips RU660/00 manual Advanced Tips and Tricks, Changing the device keys, Punch-Through Sound

AUDIO 2

6

Instructions for use

ADVANCED TIPS AND TRICKS

English	A D V I C E
	Carefully read the complete procedure before starting!

Changing the device keys

With the mode selector it is possible to select 6 categories of devices you want to operate. Each category (TV, VCR, SAT, CD, AUDIO1, AUDIO2) is meant to operate a specific group of equipment:

TV	VCR	SAT	CD/AUDIO1/AUDIO2
tv	vcr	sat	cd
	dvd	cable	amplifier
	laserdisc		miscellaneous audio
	tape		receiver
			phono

Instructions for use

Punch-Through Sound

			Punch-through sound enables you to control the audio level of	English
			your first or second TV, regardless of what device mode the
			remote control is in.
			EXAMPLE:
			You have installed a second TV under SAT mode. You can
			control that TV’s volume when you are in VCR mode. This
			feature is installed as a default setting for a first TV.
			To install this feature for a second TV:
VCR	SAT CD	AUDIO 1	1 Press the mode selector key to select VCR.
TV		AUDIO 2
1		6	2 Press and hold keys 1 and 6 simultaneously -for about 3
			seconds - until the green LED lights up.
9	9	3	3 On the keypad, press keys 9, 9, and 3.
VCR	SAT CD	AUDIO 1	4 Press the mode selector key to select SAT (second TV).
TV		AUDIO 2
			5 Press the power key.

SAT	CD
VCR	AUDIO 1
TV	AUDIO 2

1 6

Once you have programmed the functions of a device in one of the categories, it is not possible to program another device in the same category. There is, however, a solution in case you want to program two devices in the same category

(2 TV’s, VCR’s, etc.). The following example explains how.

EXAMPLE:

The SAT mode on this remote control is factory preset to control many Philips satellite receivers. You can change the SAT mode (or any mode) to operate another type of device. The following example shows you how to use the SAT mode to operate a second TV:

1 Press the mode selector key to select SAT and make sure the second TV is switched on.

2 Press and hold keys 1 and 6 simultaneously - for about 3 seconds - until the green LED lights up.

–That’s it! The LED flashes twice to indicate successful set up.

The Volume up/down keys now control the volume of your second (SAT) TV when you’re in VCR mode.

Functional back-lighting

When you pick up the SBC RU660 and tilt it over about 60 degrees, the main keys for the device you want to operate are automatically back-lit.

In VCR mode for example, only the main keys that are needed to operate the VCR are back-lit.

You can choose to have all of the keys back-lit, or you can switch off the functional back-lighting feature completely.

9	9		2 3 On the keypad, press keys 9, 9 and 2.
TV	SAT CD	AUDIO 1	4 Press the mode selector key to select TV mode.
VCR

To back-light all of the keys:

1 9 • Press keys 1 and 9 simultaneously - for about 3 seconds - until the green LED flashes twice.

1

5 Press key 1.

– The LED flashes twice to indicate successful set up. That’s it!

–The functional back-lighting is now de-activated and all keys light up when you pick up the remote control.

Pressing keys 1 and 9 simultaneously again - for about 3 seconds - will return the back-lighting to its preset functional

Don’t forget to set up the SBC RU660 to operate this second TV. See the section Set-up for use.

setting.

N O T E

The back-lighting turns off if you don’t move the remote control or if you don’t press a key within 4 seconds.

7