Philips T5VHO manual First start-up, Ballast ordering, electrical and technical data

4.Ballast specification for T5 VHO

and HO Extreme Temperature lamps

4.1.First start-up

During the first start-up of the lamps, the lamps will have a reddish/pinkish color in the middle of them. This effect is related to the mercury distribution throughout the lamp and will disappear within 2–3 minutes.

4.2. Ballast ordering, electrical and technical data

		Lamp		Maximum			Min.
No. of	Input	Starting	Catalog	Input Power	Ballast	Line Current	Starting
Lamps	Volts	Method	Number	ANSI (Watts)	Factor	(Amps)	Temp (˚F/˚C)
T5 VHO
1	277	PS	JOP-2S95-G	116W	1.1	0.42	-19/-28
1	347	PS	JOP-2S95-G	116W	1.1	0.35	-19/-28
1	480	PS	JOP-2S95-G	116W	1.1	0.24	-19/-28
2	277	PS	JOP-2S95-G	206W	1.0	0.74	-19/-28
2	347	PS	JOP-2S95-G	206W	1.0	0.59	-19/-28
2	480	PS	JOP-2S95-G	206W	1.0	0.43	-19/-28
T5 HO
1	120	PS	ICN2S5490CWL	62W	1.0	0.52	-20/-29
1	277	PS	ICN2S5490CWL	62W	1.0	0.23	-20/-29
2	120	PS	ICN2S5490CWL	120W	1.0	1.00	-20/-29
2	277	PS	ICN2S5490CWL	117W	1.0	0.43	-20/-29
1	347	PS	HCN2S5490CWL	62W	1.0	0.18	-20/-29
1	480	PS	HCN2S5490CWL	62W	1.0	0.13	-20/-29
2	347	PS	HCN2S5490CWL	120W	1.0	0.35	-20/-29
2	480	PS	HCN2S5490CWL	119W	1.0	0.25	-20/-29
3	120	PS	ICN4S5490C2LSG	182W	1.0	1.52	-20/-29
3	277	PS	ICN4S5490C2LSG	179W	1.0	0.66	-20/-29
4	120	PS	ICN4S5490C2LSG	240W	1.0	2.00	-20/-29
4	277	PS	ICN4S5490C2LSG	234W	1.0	0.86	-20/-29
3	347	PS	HCN4S5490C2LSG	188W	1.0	0.54	-20/-29
3	480	PS	HCN4S5490C2LSG	186W	1.0	0.39	-20/-29
4	347	PS	HCN4S5490C2LSG	239W	1.0	0.69	-20/-29
4	480	PS	HCN4S5490C2LSG	237W	1.0	0.50	-20/-29

Above specifications subject to change without notice.

4.3. Description of the ballast

•Quick programmed start: 1.2 second warm start, preheating the lamp electrodes; this enables the lamps to be switched on and off without reducing life.

•Intellivolt® 120–277V, 347–480V, or 277–480V: constant light independent of mains voltage fluctuations.

•End of Life Lamp (EOLL) protection: removes power to lamps upon lamp failure.

•Auto-restart cicuitry: eliminates the need to reset power mains after failed lamps are replaced.

•Low minimum starting temperature for cold applications.

10 OEM Design Guide Philips T5 VHO and HO Extreme Temperature Lamps and Ballasts