PHL Audio B17 specifications 6.5’’ Bass Midrange Drivers, 1330, 1290

1330 ■ 1290

6.5’’ Bass Midrange Drivers
		1330		1290
TYPICAL CHARACTERISTICS
Rated impedance	Z	8		16		Ω
Reference efficiency (1 W@1 m)	-	94		94		dB SPL
Usable frequency range 1	-	50–4000		50–4000		Hz
Power handling capacity 2 (AES)	-	100		100		W
Max Sound Pressure Level 3	SPLmax	110		110		dB SPL
Min. impedance modulus	Zmin	6.6 @ 370Hz 14.2 @ 330Hz				Ω
Voice-coil inductance 4 @ 1 kHz	Le1k	0.72		1.36		mH
@ 10 kHz	Le10k	0.31		0.50		mH
Bl product	Bl	10.50		13.10		N/A
Moving mass	Mms	0.012		0.012		Kg
THIELE-SMALL PARAMETERS : TYPICAL (QC LIMITS)
Resonance frequency 5	Fs	53 (±8)		53 (±8)		Hz
DC resistance 6	Re	6.1 (±0.6)		12.1 (±1.2)		Ω
Mechanical quality factor	Qms	3.6		3.6		1
Electrical quality factor	Qes	0.22		0.29		1
Total quality factor	Qts	0.21		0.26		1
Mechanical suspension compliance	Cms	750		750	10-6m/N
Effective piston area	S	0.0143		0.0143		m2
	d
Equivalent Cas air load	Vas	0.022		0.022		m3
Max. linear excursion	Xmax	±3.5		±3.5		mm
Linear displacement volume	Vd	0.050		0.050		10-3 m3
Half-space efficiency		1.4		1.1		%
Unity load volume	Vas Qts2	0.9		1.5		10-3 m3
ABSOLUTE MAXIMUM RATINGS
Short term max. input voltage 7	Vmax	60		85		V
Max. excursion before damage	Xdam	8.0		8.0		mm
Ambient operating temperature		–10	to	+50		°C
Storage temperature 8		–20	to	+70		°C
Environmental conditions 9		Outdoor
APPLICATION INFORMATION
Air volume occupied by the driver 10		0.5		0.5		10-3 m3
Speaker net mass		2.15		2.15		Kg
Recommended reflex box	Vb/Fb	12L / 65 Hz				L / Hz
Electrical polarity	A positive voltage applied on the red
	terminal produces forward cone motion.

max.187.5	angles)(on	PHYSICAL CHARACTERISTICS
		4 x Ø 5.3 Holes on Ø 172
Ø
+ Red dot
ONAST F
8.0 x35 .6	inalerm T

Ø 162.5 max.

8

68.5 max.

Ø 117.5 max.

Ø 145.3 max.

SPECIFICATION NOTES

Note 1 : Allowing for energy response, excursion capability, Power spectrum, and -3dB low freq. roll-off for standard reflex tuning.

Note 2 : Established at 20°C ambient temp, according to AES2-1984 standard using IEC268-1 simulated programme signal and a 12 liter Bass-Reflex test enclosure tuned at 55Hz.

Note 3 : Established at 1m on axis of the loudspeaker mounted

in test enclosure, when driven at full AES Power Handling Capacity, including 4dB of thermal compression loss.

Note 4 : Measured at 20 mA in free air.

Note 5 : Measured at 20 mA and 20°C ambient temp. in free air conditions, after full run and rest.

Note 6 : Measured at 20°C ambient temp.

QC limits are ±10%

Note 7 : Stated in RMS voltage according to IEC 268-5.

Note 8 : Includes shipping conditions. The lower limit prevents from demagnetization.

Note 9: Our products are classified in three categories : Indoor, Outdoor, and Outdoor✚ for permanent outdoor use or severe conditions.

Note 10 : Calculated for front mounting on to a 18 mm thick board.

461, rue des chênes ■ Z.A 77590 CHARTRETTES FRANCE

Tél : 33 01 64 81 29 80

Fax : 33 01 60 69 10 28

e-mail : phlaudio@phlaudio.com

http: //www.phlaudio.com

PHL Audio S.A. provides these specifications as representative of current production after conditioning. Because of our continuous research, they are subject to change without notice.