10 iN, Jobsite, Table SAW, Model no | Sears 137.28463 guide

10 iN, JOBSITE		TABLE SAW	MODEL NO. 137.284630
PARTS LiST FOR MOTOR
i.D.	Description		Size	QTy
3089	FIELD ASS'Y			1
OHX9	NEEDLE BEARING			1
OJXS	HEX. SOC. SETSCREW		MS_J.8-8	2
OKCN	CR. RE. PAN HEAD TAPPING & WA3HERSCREW		M5"12'-50	2
OKTK	STRAIN RELIEF			1
OQFE	BRUSH COVER			2
OQFF	CARBON	BRUSH ASS'Y		2
OQFG	BRUSH HOLDER A,SS'Y			2
145Y	CR. RE. PAN HD. SCREW & WASHER		M5_,8-55	4
2DW9	WAVE WASHER			1
2RPP	FLOW GUIDE			1
2RRD	CUTTER SHAFT ASS'Y			1
2RWS	CR. RE. COUNTER-SUN HEAD SCREW		M5_3.8-10	2
2YE5	BRACKET			1
2YH8	MOTOR	COVER		1
2YK4	ARMATURE ASS'Y			1
2YK7	LABEL			1

\

k

\

\

/2RPP

\

'\

/...OKCN_

fqFFz

_QFG_

2YH8

Image 49

Sears 137.28463 operating instructions 10 iN, Jobsite, Table SAW, Model no, Parts LiST for Motor

Contents

Operators Manual Section Blade Size MotorSAW Support and Clamp Work PROHiBiTiON Wear Proper Apparel Generalsafety iNSTRUCTiONS Secure Page Alwaysusesawblade Page Kickbacks Grounding iNSTRUCTiONS Power Supply and Motor SPECiFiCATiONSImmediately La, Caution 308K Dado Insert Plate Recommended AccessoriesSupplied not Supplied Loose Parts SAW Description Quantity Obtained and is installed correctlyStand STU ACD EFG H KLM Stand lock hook Page Revolutions PER Minute RPM Overload Reset Switch Do not release the stand hooks Order to Avoid iNJURY Fig. D Setting UP the Stand ANTI-KICKBACK Pawls Installing the Blade Guard Storage Clamps Fig. N Installing the Power CordAssembling the Blade ELEVATION/TILT Handwheel Fig. Q Installing the Rear Table Riving Knife Assembly Fig. W Adjustments Fig. Y Blade Guard AssemblyAnti=kickback pawl assembly Fig. Z, AA, BB Additional Blade Fig. Z Fig. DD Improper riving knife alignment can Adjusting the Miter Gauge RiP Fence Adjustment Fig. FF Adjusting the Table iNSERT Fig. JJ-1 Power source when making any adjustments BLADETiLTiNG Scale iNDiCATORTo prevent personal injury Basic SAW Operations ON/OFF Switch Fig. NNTilting the Blade Never USE the TWO AT the Same Time Cutting Operations TurnthesawONandwaitforthe bladetocometofullspeed Helpful Devices Ripping Small Pieces Push Block Auxiliary Fence Fig. TTMake a Push Block Fig. UU Making the base Fig. WW To prevent serious injury MiTERiNG Fig. ZZ Compound Miter Crosscutting00~45 Miter Angle NON-THROUGH Fig. bb For your own safety, always replace Do not use Adjustable or Wobble type dadoesDADOCUTSFIG. cc, dd Blade Raising and Tilting Maintaining Your Table SAW General MaintenanceMechanism Fig. ee, ff LUBRiCATiON Clean the Blade Tilting Scale IndicatorReplacing the Carbon Causes Corrective Problem PossibleAction Tilting Cut Here To WAR.I.Gi 10 iN. Jobsite Table SAW Model NO= 137=284630 Schematic a 10 iN, Jobsite Parts LiST for MotorTable SAW Model no 10 IN. Jobsite Table SAW Parts LiST for Stand Service Sears Installation Service Wv sears,tom Wvvv.sears.ca OurHome