Obtained and is installed correctly, Stand | Sears 137.28463

Separate all parts from packing materials. Check each part with the

illustration on the next page and the "Table of Loose Parts" to make certain

all items are accounted for, before discarding any packing material.

NOTE: To make assembly easier, keep contents of box together.

I,A WARNING ]

if any part is missing or damaged, do not attempt to assemble the table saw, plug in the power cord, or turn the switch ON until the missing or damaged part is

obtained and is installed correctly.

Call 1=800-843-1682 for missing or damaged parts.

	TABLE	OF LOOSE		PARTS
	TABLE	SAW
	ITEM	DESCRIPTION					QUANTITY
	A	Table	saw assembly				1
	B	Blade guard assembly					1
	C	Blade guard assembly					1
	C	Anti-kickback			pawls	assembly	1
	D	Riving	knife hardware bag assembly				1
	E	Rip fence					1
	F	Rip fence					1
	F	Miter gauge					1
	G	Blade wrench					2
	H	Hex wrench					1
	I	Push	stick				1
	J	Rear table		extension			1
	K	Rear table		extension		tube	2
	L	Power	cord storage				1
	M	Table extension wing hardware bag assembly					1
	N	Blade					1
	O	Dust bag					1
	P	Handwheel			handle hardware bag		1
	Q	Hex bolts, washers					4 each
	R	Leg handle hardware				assembly	1
	STAND
	S	Riving	knife storage			(locking handle)	1 set
		Riving	knife storage			(locking handle)	1 set
		Blade	guard		storage,	screws
	T	Roller wheel			hardware assembly		2
	U	Stand					1

Image 14

Sears 137.28463 operating instructions Obtained and is installed correctly, Loose Parts SAW Description Quantity, Stand

Contents

Operators Manual Section SAW MotorBlade Size PROHiBiTiON Support and Clamp Work Generalsafety iNSTRUCTiONS Wear Proper Apparel Secure Page Alwaysusesawblade Page Kickbacks Immediately Power Supply and Motor SPECiFiCATiONSGrounding iNSTRUCTiONS La, Caution Supplied not Supplied Recommended Accessories308K Dado Insert Plate Stand Obtained and is installed correctlyLoose Parts SAW Description Quantity ACD EFG H KLM STU Stand lock hook Page Overload Reset Switch Revolutions PER Minute RPM Order to Avoid iNJURY Do not release the stand hooks Setting UP the Stand Fig. D Installing the Blade Guard ANTI-KICKBACK Pawls Assembling the Blade Installing the Power CordStorage Clamps Fig. N ELEVATION/TILT Handwheel Installing the Rear Table Fig. Q Riving Knife Assembly Fig. W Anti=kickback pawl assembly Fig. Z, AA, BB Blade Guard AssemblyAdjustments Fig. Y Additional Blade Fig. Z Improper riving knife alignment can Fig. DD RiP Fence Adjustment Fig. FF Adjusting the Miter Gauge Adjusting the Table iNSERT Fig. JJ-1 To prevent personal injury BLADETiLTiNG Scale iNDiCATORPower source when making any adjustments Tilting the Blade ON/OFF Switch Fig. NNBasic SAW Operations Cutting Operations Never USE the TWO AT the Same Time TurnthesawONandwaitforthe bladetocometofullspeed Ripping Small Pieces Helpful Devices Make a Push Block Fig. UU Making the base Auxiliary Fence Fig. TTPush Block To prevent serious injury Fig. WW 00~45 Miter Angle Compound Miter CrosscuttingMiTERiNG Fig. ZZ Fig. bb NON-THROUGH DADOCUTSFIG. cc, dd Do not use Adjustable or Wobble type dadoesFor your own safety, always replace Mechanism Fig. ee, ff Maintaining Your Table SAW General MaintenanceBlade Raising and Tilting Replacing the Carbon Clean the Blade Tilting Scale IndicatorLUBRiCATiON Action Problem PossibleCauses Corrective Tilting Cut Here To WAR.I.Gi Schematic a 10 iN. Jobsite Table SAW Model NO= 137=284630 Table SAW Parts LiST for Motor10 iN, Jobsite Model no Parts LiST for Stand 10 IN. Jobsite Table SAW Sears Installation Service Service OurHome Wv sears,tom Wvvv.sears.ca