Pioneer manual 40

Section
20		System settings
	5 Touch Start to display the data transfer		You can also switch the rear view image by
	mode.		pressing the touch key.
	# Follow the on-screen instructions to finish updat-		For details refer to Using the rear view on page
	ing the Bluetooth software.		10.
			! After you set up the rear view camera setting,
	Displaying the Bluetooth		move the shift lever to REVERSE (R) and
			confirm that the rear view camera video is
	system version		shown on the display.
	If this unit fails to operate properly, you may		! Change this setting if the display switches to
			the rear view camera video by error while you
	need to consult your dealer for repair. In such
			are driving forward.
	cases, you may be asked to specify the system
			! To stop watching the rear view camera video
	version. Perform the following procedure to
			and return to the source display, press and
	check the version on this unit.
			hold MUTE.
	1 Turn the source off.		! Touch the RearView source icon to display
			the rear view camera image while driving.
	Refer to Turning the source ON/OFF on page 8.
			Touch the source icon again to turn the rear
	2 Press the home button to switch to the		view camera off. For details, refer to Selecting
			a source on page 8.
	home display.
	3 Touch the system key to open the system		1 Press the home button to switch to the
			home display.
	menu.
	4 Touch Bluetooth Version Information to		2 Touch the system key to open the system
			menu.
	display to the version of the Bluetooth mod-
	ule of this unit.		3 Touch Camera Polarity on the system
			menu to select the appropriate setting.

System settings

Auto EQ (auto-equalizing)	Before operating the auto EQ
The auto-equalizer automatically measures the	function
	!	Carry out auto EQ in as quiet a place as pos-
car’s interior acoustic characteristics, and then
creates an auto-equalizer curve based on that in-		sible, with the car engine and air condition-
formation.		ing switched off. Also cut power to car
! To perform this function, dedicated micro-		phones or portable telephones in the car, or
phone (e.g. CD-MC20) is required.		remove them from the car before carrying
		out auto EQ. Sounds other than the measure-
WARNING		ment tone (surrounding sounds, engine
		sound, telephones ringing etc.) may prevent
As a loud tone (noise) may be emitted from the		correct measurement of the car interior
speakers when measuring the car’s interior		acoustic characteristics.
acoustic characteristics, never perform auto EQ	!	Be sure to carry out auto EQ using the op-
while driving.		tional microphone. Using another micro-
		phone may prevent measurement, or result
CAUTION		in incorrect measurement of the car interior
		acoustic characteristics.
! Thoroughly check the conditions before per-
	!	In order to perform auto EQ, the front speak-
forming auto EQ as the speakers may be
		er must be connected.
damaged if these functions are performed
	!	When this unit is connected to a power amp
when:
		with input level control, auto EQ may not be
— The speakers are incorrectly connected. (For
		possible if the power amp’s input level is set
example, when a rear speaker is connected
		below the standard level.
as a subwoofer output.)
	!	When this unit is connected to a power amp
— A speaker is connected to a power amp deliv-
		with an LPF, turn this LPF off before perform-
ering output higher than the speaker’s maxi-
		ing auto EQ. Also set the cut-off frequency
mum input power capability.
		for the built-in LPF of an active subwoofer to
! If the microphone is placed in an unsuitable
		the highest frequency.

Setting the rear view camera (back up camera)

CAUTION

Pioneer recommends the use of a camera which outputs mirror-reversed images. Oth- erwise, the screen image will appear re- versed.

This unit features a function that automatically switches to the rear view camera video (R.C IN) when a rear view camera is installed on your car and the shift lever is moved to the REVERSE

(R)position. (For more details, consult your dealer.)

!Battery – When the polarity of the connected lead is positive while the shift lever is in RE- VERSE (R) position

!Ground – When the polarity of the connected lead is negative while the shift lever is in RE- VERSE (R) position

!Off – When a rear view camera is not con- nected to this unit

!The rear view key setting also turns off on the home display screen.

position the measurement tone may become	The distance has been calculated by com-
!
loud and measurement may take a long	puter to be the optimum delay to give accu-

time, resulting in battery drainage. Be sure	rate results for the circumstances, so please
to place the microphone in the specified lo-
	continue to use this value.
cation.
	— The reflected sound within the car is
	strong and delays occur.
	— The LPF on active subwoofers or external
	amps delay the lower sounds.
	! Auto EQ changes the audio settings as fol-
	lows:
	— The fader/balance settings return to the
	center position. (Refer to Using fader/bal-
	ance adjustment on page 33.)

40En