Pioneer CDS-P4000 specifications Before Using This Product, Using the CD Player, Display Modes

Before Using This Product

About This Manual

Operate this CD Player with a Head Unit connected. For details concerning operation, refer to the back page of this manual.

Important

The serial number of this device is located on the bottom of this product. For your own secu- rity and convenience, be sure to record this number on the enclosed warranty card.

Resetting the Microprocessor

The microprocessor must be reset under the following conditions:

When using this product for the first time after installation.

When the machine fails to operate properly.

When strange (incorrect) messages appear on the display.

Precaution

CAUTION: USE OF CONTROL OR ADJUSTMENT OR PERFOR- MANCE OF PROCEDURES OTHER THAN THOSE SPEC- IFIED HEREIN MAY RESULT IN HAZARDOUS RADIA- TION EXPOSURE.

CAUTION: THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE EYE HAZARD.

•Keep this manual handy as a reference for operating procedures and precautions.

•Protect the product from moisture.

After-sales Service for Pioneer Products

Using the CD Player

Playing the CD Player

The CD player plays one standard 12 cm or 8 cm CD at a time. Do not use any adapter when playing a 8 cm CD.

1. Insert the disc with the label side up.

Lights up when a CD is loaded.

Lights up when a CD is playing.

2. For details concerning operation, refer to the back page of this manual.

Display Modes

Level Indicator Display

This product has eight display patterns (Mode 1 to Mode 8) from which you can choose one at a time.

• Selecting the Level Indicator display.

Each press changes the Display ...

Each press of the DISPLAY button changes the display in the following order:

Mode 1 Ô Mode 2 Ô Mode 3 Ô Mode 4 Ô Mode 5

ÔMode 6 Ô Mode 7 Ô Mode 8 Ô Mode 1 ...

•To reset the microprocessor, press the RESET button with a pen tip or other pointed instrument.

Please contact the dealer or distributor from where you purchased the product for its after- sales service (including warranty conditions) or any other information. In case the necessary information is not available, please contact the companies listed below:

Please do not ship your product to the companies at the addresses listed below for repair without advance contact.

7U.S.A. 7CANADA

3. Remove the disc.

Note:

Mode 1, Mode 2, Mode 3 and Mode 4 Segments light from left to right according to the audio level.

Mode 5

Segments light from the center, and expand towards the sides according to the audio level.

Example: Mode 1

Example: Mode 5

Pioneer Electronics Service, Inc.	Pioneer Electronics of Canada, Inc.
CUSTOMER SERVICE	CUSTOMER SATISFACTION
DEPARTMENT	DEPARTMENT
P.O. Box 1760	300 Allstate Parkway
Long Beach, CA 90801	Markham, Ontario L3R OP2
800-421-1404	(905) 479-4411
	1-877-283-5901

For warranty information please see the Limited Warranty sheet included with your product.

•A disc left partially inserted after ejection may incur damage or fall out.

•If a disc cannot be inserted fully or playback fails, make sure the recorded side is down. Press the EJECT button and check the disc for damage before reinserting it.

•If a CD is inserted with the recorded side up, it will be ejected automatically after a few moments.

•If the CD player cannot operate properly, an error message (such as “ERROR-14”) appears on the head unit display. Refer to “CD Player Troubleshooting”.

•Do not insert anything other than a CD into the CD Loading Slot.

Mode 6

Display shows segments rotating from left to right.

Mode 7

Depending on the audio level, different segments light up.

Mode 8

Display turns off except for the “DISC SET” and “PLAY” indications.

Example: Mode 6

Example: Mode 7

Example: Mode 8