Section |
|
|
| |
03 |
|
| Installation |
|
|
| j When using a subwoofer of 70 W (2 W), be | Installation | |
|
| |||
|
| |||
|
|
| sure to connect the subwoofer to the violet | Important |
|
|
| and violet/black leads of this unit. Do not | |
|
|
| ! Check all connections and systems before | |
|
|
| connect anything to the green and green/ |
Installation
Use commercially available parts when instal- | # Make sure that the unit is installed securely in |
ling. | place. An unstable installation may cause skipping |
| or other malfunctions. |
black leads. | final installation. | |
k Not used. | ! Do not use unauthorized parts as this may | |
l Subwoofer (4 W) × 2 | cause malfunctions. | |
Notes | ! Consult your dealer if installation requires | |
drilling of holes or other modifications to the | ||
! With a 2 speaker system, do not connect any- | ||
vehicle. | ||
thing to the speaker leads that are not con- | ! Do not install this unit where: | |
nected to speakers. | — it may interfere with operation of the vehicle. | |
! Change the initial menu of this unit. Refer to | — it may cause injury to a passenger as a result | |
of a sudden stop. | ||
! The semiconductor laser will be damaged if | ||
The subwoofer output of this unit is monau- | it overheats. Install this unit away from hot | |
ral. | places such as near the heater outlet. | |
Power amp (sold separately) | ! Optimum performance is obtained when the | |
unit is installed at an angle of less than 60°. | ||
Perform these connections when using the op- |
| |
tional amplifier. | 60° | |
|
13
| 2 |
|
|
|
| | | 4 | ! When installing, to ensure proper heat dis- |
|
| |||
5 |
| 5 |
| |
|
| persal when using this unit, make sure you | ||
| | |
| |
|
| 3 |
| leave ample space behind the rear panel and |
1 | 2 |
| 6 | wrap any loose cables so they are not block- |
| | | ing the vents. | |
|
| |||
7 |
| 7 |
|
|
| | |
|
|
DIN Front-mount
1 Insert the mounting sleeve into the dash- board.
For installation in shallow spaces, use the supplied mounting sleeve. If there is enough space, use the mounting sleeve that came with the ve- hicle.
2 Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place.
1
2
1Dashboard
2Mounting sleeve
3 Install the unit as illustrated.
1
2
DIN Rear-mount
1Determine the appropriate position where the holes on the bracket and the side of the unit match.
2 Tighten two screws on each side.
1 | 3 |
|
2
1Truss screw (5 mm × 8 mm)
2Mounting bracket
3Dashboard or console
Removing the unit
1 Remove the trim ring.
1 | System remote control |
| Connect to Blue/white cable. |
2 | Power amp (sold separately) |
3 | Connect with RCA cables (sold separately) |
4 | To Front output |
Leave ample | 5 cm |
space |
|
| 5 cm 5cm |
3
4
5
5 | Front speaker |
6 | To Rear output or subwoofer output |
7 | Rear speaker or subwoofer |
1 | Nut |
2 | Firewall or metal support |
3 | Metal strap |
1Trim ring
2Notched tab
DIN front/rear mount
This unit can be properly installed using either
10En
4 | Screw |
5 | Screw (M4 × 8) |
!Releasing the front panel allows easier ac- cess to the trim ring.
!When reattaching the trim ring, point the side with the notched tab down.