Section

 

 

 

 

 

 

02

 

 

Operating this unit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The unit can automatically search for a different

FM STEP (FM tuning step)

 

 

 

 

 

 

 

 

Operating this unit

System menu

Turning the display off or on

station with the same programming, even during

 

Normally, the FM tuning step employed by seek

preset recall.

 

 

tuning is 50 kHz. When AF or TA is on, the tuning

1

Press M.C. to turn Auto PI seek on or off.

 

 

step automatically changes to 100 kHz. It may be

 

 

 

AUX (auxiliary input)

 

preferable to set the tuning step to 50 kHz when

Activate this setting when using an auxiliary de-

 

AF is on.

 

! The tuning step remains at 50 kHz during man-

vice connected to this unit.

 

 

ual tuning.

1

Press M.C. to turn AUX on or off.

 

 

1 Press M.C. to select the FM tuning step.

 

 

 

50 (50 kHz)—100 (100 kHz)

1

Press and hold SRC/OFF until the unit

turns off.

2

Press and hold M.C. until the main menu

appears in the display.

3

Turn M.C. to change the menu option

and press to select SYSTEM.

4

Turn M.C. to select the system menu

%Press and hold DISP/DISP OFF until the display turns on or off.

If an unwanted display appears

Turn off the unwanted display using the procedures listed below.

1 Press M.C. to display the main menu.

Switching the dimmer setting

You can adjust the brightness of illumination.

1Press M.C. to display the main menu.

2Turn M.C. to display ILLUMI and press to select.

3Press M.C. to select the desired setting. OFF (off)—ON (on)

!You can also change the dimmer setting by pressing and holding /DIMMER.

Initial menu

1 Press and hold SRC/OFF until the unit

turns off.

MW STEP (MW tuning step)

The MW tuning step can be switched between 9 kHz and 10 kHz.

1Press M.C. to select the MW tuning step. 9 (9 kHz)—10 (10 kHz)

SP-P/O MODE (rear output and preout setting)

The rear speaker leads output and the RCA output of this unit can be used to connect a full-range speaker or subwoofer. Select a suitable option for your connection.

1

Press M.C. to display the setting mode.

2

Turn M.C. to select the desired setting.

 

You can select any one of the options in the fol-

 

lowing list:

 

! REAR/SUB.W – Select when there is a full-

 

range speaker connected to the rear speak-

 

er leads output and there is a subwoofer

 

connected to the RCA output.

function.

Once selected, the following system menu func-

tions can be adjusted.

For details, refer to System menu on the pre-

vious page.

Using an AUX source

1Insert the stereo mini plug into the AUX input jack.

2Press SRC/OFF to select AUX as the source.

Note

AUX cannot be selected unless the auxiliary setting is turned on. For more details, refer to AUX (auxiliary input) on this page.

2

Turn M.C. to change the menu option

and press to select SYSTEM.

3

Turn M.C. to display DEMO OFF and press

to select.

4

Turn M.C. to switch to YES.

5

Press M.C. to select.

2

Press and hold M.C. until the main menu

appears in the display.

3

Turn M.C. to change the menu option

and press to select INITIAL.

4

Turn M.C. to select the initial menu func-

tion.

Once selected, the following initial menu func-

tions can be adjusted.

8 En

! SUB.W/SUB.W – Select when there is a

subwoofer connected directly to the rear

speaker leads output without any auxiliary

amp and there is a subwoofer connected

to the RCA output.

! REAR/REAR – Select when there is a full-

range speaker connected to the rear speak-

er leads output and the RCA output.

If there is a full-range speaker connected to

the rear speaker leads output and the RCA

output is not used, you may select either

REAR/SUB.W or REAR/REAR.

Switching the display

Selecting the desired text information

1Press DISP/DISP OFF to cycle between the fol- lowing:

!Source name

!Source name and clock