Operating this unit

Operating this unit

Section

02

S.RTRV (sound retriever)

Automatically enhances compressed audio and restores rich sound.

1Press M.C. to select the desired setting. For details, refer to Enhancing compressed audio and restoring rich sound (sound retriever) on the previous page.

Audio adjustments

1Press M.C. to display the main menu.

2Turn M.C. to change the menu option and press to select AUDIO.

3Turn M.C. to select the audio function. Once selected, the following audio functions can be adjusted.

!FADER is not available when SUB.W/SUB.W is selected in SP-P/O MODE. For details, refer to SP-P/O MODE (rear output and preout set- ting) on the next page.

!SUB.W, SUB.W CTRL and HPF SETTING are not available when REAR/REAR is selected in SP-P/O MODE. For details, refer to

SP-P/O MODE (rear output and preout set- ting) on the next page.

!SUB.W CTRL and HPF SETTING are not avail- able when SUB.W is selected in OFF. For de- tails, refer to SUB.W (subwoofer on/off setting) on this page.

FADER (fader adjustment)

1Press M.C. to display the setting mode.

2Turn M.C. to adjust the front/rear speaker bal- ance.

BALANCE (balance adjustment)

1Press M.C. to display the setting mode.

2Turn M.C. to adjust the left/right speaker bal- ance.

EQ SETTING (equalizer recall)

1Press M.C. to display the setting mode.

2Turn M.C. to select the equalizer.

POWERFUL—NATURAL—VOCAL—CUS- TOM1—CUSTOM2—FLAT—SUPER BASS The equalizer band and equalizer level can be customized when CUSTOM1 or CUSTOM2 is selected.

If selecting CUSTOM1 or CUSTOM2, complete the procedures outlined below. If selecting other options, press M.C. to return to the pre- vious display.

!CUSTOM1 can be set separately for each source.

!CUSTOM2 is a shared setting used in com- mon for all sources.

3Press M.C. to display the setting mode.

4Press M.C. to cycle between the following: Equalizer band—Equalizer level

5Turn M.C. to select the desired setting. Equalizer band: 80HZ—250HZ—800HZ— 2.5KHZ—8KHZ

Equalizer level: +6 to –6

!You can also switch the equalizer by pressing repeatedly.

LOUDNESS (loudness)

Loudness compensates for deficiencies in the low- frequency and high-frequency ranges at low vol- ume.

1Press M.C. to select the desired setting.

OFF (off)—LOW (low)—MID (mid)—HI (high)

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output which can be turned on or off.

1Press M.C. to select the desired setting. NOR (normal phase)—REV (reverse phase)— OFF (subwoofer off)

SUB.W CTRL (subwoofer adjustment)

Only frequencies lower than those in the selected range are outputted from the subwoofer.

1Press M.C. to display the setting mode.

2Press M.C. to cycle between the following: Cut-off frequency—Output level—Slope level Rates that can be adjusted will flash.

3Turn M.C. to select the desired setting. Cut-off frequency: 50HZ—63HZ—80HZ— 100HZ—125HZ—160HZ—200HZ Output level: –24 to +6

Slope level: –6— –12

BASS BOOST (bass boost)

1Press M.C. to display the setting mode.

2Turn M.C. to select a desired level.

0 to +6 is displayed as the level is increased or decreased.

HPF SETTING (high pass filter adjustment)

When you do not want low sounds from the sub- woofer output frequency range to play from the front or rear speakers, turn on the HPF (high pass filter). Only frequencies higher than those in the selected range are output from the front or rear speakers.

1Press M.C. to display the setting mode.

2Press M.C. to cycle between the following: Cut-off frequency—Slope level

3Turn M.C. to select the desired setting. Cut-off frequency: OFF—50HZ—63HZ—80HZ

—100HZ—125HZ—160HZ—200HZ Slope level: –6— –12

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the volume level of each source to prevent radical changes in volume when switching between sour- ces.

!Settings are based on the FM volume level, which remains unchanged.

!The MW volume level can also be adjusted with this function.

!When selecting FM as the source, you cannot switch to SLA.

1Press M.C. to display the setting mode.

2Turn M.C. to adjust the source volume. Adjustment range: +4 to –4

System menu

1Press M.C. to display the main menu.

2Turn M.C. to change the menu option and press to select SYSTEM.

3Turn M.C. to select the system menu function.

Once selected, the following system menu func- tions can be adjusted.

CLOCK SET (setting the clock)

1Press M.C. to display the setting mode.

2Press M.C. to select the segment of the clock display you wish to set.

Hour—Minute

3Turn M.C. to adjust the clock.

12H/24H (time notation)

1Press M.C. to select the desired setting. 12H (12-hour clock)—24H (24-hour clock)

AUTO PI (auto PI seek)

English

En

7