Section

 

02

Operating this unit

 

Function settings

Operating this unit

 

 

FAD/BAL (fader/balance adjustment)

1 Press M.C. to display the main menu.

 

1 Press M.C. to display the setting mode.

 

 

2 Turn M.C. to change the menu option

 

2 Press M.C. to cycle between fader (front/rear)

 

and balance (left/right).

and press to select FUNCTION.

 

 

3 Turn M.C. to adjust the speaker balance.

 

 

3 Turn M.C. to select the function.

 

! When the rear output and RCA output set-

 

ting are SW, you cannot adjust front/rear

After selecting, perform the following proce-

 

 

speaker balance. Refer to SW CONTROL

dures to set the function.

 

 

(rear output and subwoofer setting) on the

 

 

BOOK MARK (bookmark)

 

next page.

 

 

 

 

PRESET EQ (equalizer recall)

1Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

1

Press M.C. to display the setting mode.

For details, refer to Storing song information

2

Turn M.C. to select an equalizer curve.

(Bookmark) on the previous page.

 

 

POWERFUL—NATURAL—VOCAL—CUS-

3 Press M.C. to confirm the selection.

 

 

TOM1—CUSTOM2—FLAT—SUPER BASS

PAUSE (pause)

3

Press M.C. to confirm the selection.

 

 

GRAPHIC EQ (equalizer adjustment)

1 Press M.C. to pause or resume.

 

 

You can adjust the currently selected equalizer

 

 

S.RTRV (sound retriever)

 

 

curve setting as desired. Adjusted equalizer curve

1 Press M.C. to display the setting mode.

 

settings are stored in CUSTOM1 or CUSTOM2.

!

A separate CUSTOM1 curve can be created

2 Turn M.C. to select the desired setting.

 

 

for each source. If you make adjustments

For details, refer to Enhancing compressed

 

 

 

 

when a curve other than CUSTOM2 is se-

audio and restoring rich sound (sound retriever)

 

 

 

 

lected, the equalizer curve settings will be

on the previous page.

 

 

 

 

stored in CUSTOM1.

3 Press M.C. to confirm the selection.

 

 

!

A CUSTOM2 curve that is common for all

 

 

 

sources can be created. If you make adjust-

Audio Adjustments

 

 

ments when the CUSTOM2 curve is selected,

 

 

the CUSTOM2 curve will be updated.

1 Press M.C. to display the main menu.

1

Press M.C. to display the setting mode.

2

Press M.C. to cycle between equalizer band

 

2 Turn M.C. to change the menu option

 

 

and level.

3

Press M.C. to switch to equalizer band and

and press to select AUDIO.

 

 

then turn M.C. to select.

 

 

 

3 Turn M.C. to select the audio function.

 

 

100HZ—315HZ—1.25KHZ—3.15KHZ—8KHZ

4

Press M.C. to switch to level and then turn M.

 

After selecting, perform the following proce-

C. to adjust.

dures to set the audio function.

Adjustment range: +6 to –6

 

 

LEVEL METER (level meter display setting)

1Press M.C. to display the setting mode.

2Turn M.C. to select the desired setting. OFF (off)—MODE1—MODE2—MODE3— MODE4

3Press M.C. to confirm the selection.

LOUDNESS (loudness)

Loudness compensates for deficiencies in the low- and high-frequency ranges at low volume.

1Press M.C. to display the setting mode.

2Turn M.C. to select the desired setting. OFF (off)—LOW (low)—MID (mid)—HIGH (high)

3Press M.C. to confirm the selection.

SW SETTING 1 (subwoofer on/off setting)

This unit is equipped with a subwoofer output which can be turned on or off.

1Press M.C. to display the setting mode.

2Turn M.C. to select the desired setting. NORMAL (normal phase)—REVERSE (reverse phase)—OFF (subwoofer off)

3Press M.C. to confirm the selection.

SW SETTING 2 (subwoofer adjustment)

The cut-off frequency and output level can be adjusted when the subwoofer output is on.

Only frequencies lower than those in the selected range are outputted from the subwoofer.

1Press M.C. to display the setting mode.

2Press M.C. to cycle between the cut-off fre- quency and output level of the subwoofer.

3Press M.C. to switch to cut-off frequency and then turn M.C. to select the cut-off frequency. 50HZ—63HZ—80HZ—100HZ—125HZ

4Press M.C. to switch to output level and then turn M.C. to adjust the output level. Adjustment range: +6 to -24

HPF SETTING (high pass filter adjustment)

When you do not want low sounds from the sub- woofer output frequency range to play from the front or rear speakers, turn on the HPF (high pass filter). Only frequencies higher than those in the selected range are output from the front or rear speakers.

1Press M.C. to display the setting mode.

2Turn M.C. to select the cut-off frequency. OFF (off)—50HZ—63HZ—80HZ—100HZ— 125HZ

3Press M.C. to confirm the selection.

BASS BOOSTER (bass boost)

1Press M.C. to display the setting mode.

2Turn M.C. to adjust the level. Adjustment range: 0 to +6

3Press M.C. to confirm the selection.

SLA (source level adjustment)

SLA (Source Level Adjustment) lets you adjust the volume level of each source to prevent radical changes in volume when switching between sour- ces.

!When selecting FM as the source, you cannot switch to SLA.

!Settings are based on the FM volume level, which remains unchanged.

!The AM volume level can also be adjusted with

this function.

1Press M.C. to display the setting mode.

2Turn M.C. to adjust the source volume. Adjustment range: +4 to –4

3Press M.C. to confirm the selection.

Initial Settings

1Press and hold SRC/OFF until the unit turns off.

2Press M.C. and hold until the initial set- ting menu appears in the display.

10En