Operating this unit
Operating this unit
Section
02
3Turn M.C. to select the initial setting. After selecting, perform the following proce- dures to set the initial setting.
CLOCK SET (setting the clock)
1Press M.C. to display the setting mode.
2Press M.C. to select the segment of the clock display you wish to set.
3Turn M.C. to adjust the clock.
AUX (auxiliary input)
Activate this setting when using an auxiliary device connected to this unit.
1Press M.C. to turn AUX on or off.
USB PNP (plug and play)
This setting allows you to switch your source to
1 Press M.C. to turn the plug and play function |
on or off. |
ON – When a USB storage device/iPod is con- |
nected, depending on the type of device, the |
source is automatically switched to USB/USB- |
The rear speaker leads output and RCA output can be used for
If you switch to REAR SP :SW, you can connect a rear speaker lead directly to a subwoofer without using an auxiliary amp.
Initially, REAR SP is set for rear
1Press M.C. to display the setting mode.
2Turn M.C. to change the output and press to select.
REAR
3Turn M.C. to change the setting.
REAR SP:
PREOUT:
!Even if you change this setting, there will be no output unless you turn the sub- woofer output on (refer to SW SETTING 1 (subwoofer on/off setting) on the previous page).
!If you change this setting, subwoofer out- put in the audio menu will return to the fac- tory settings.
4Press M.C. to confirm the selection.
Direct selection from the illumination color list
1Press M.C. to display the main menu.
2Turn M.C. to change the menu option and press to select ILLUMINATION.
3Turn M.C. to select KEY COLOR (button il- lumination) or LCD COLOR (display illumina- tion); press to confirm.
4Turn M.C. to select the illumination color. You can select one option from the following list.
!30 preset colors (WHITE to ROSE)
!SCAN (cycle through all colors)
!CUSTOM (customized illumination color)
5Press M.C. to confirm the selection.
Notes
!When SCAN is selected, the illuminated color automatically cycles through the 30 preset colors.
!When CUSTOM is selected, the customized color saved is selected.
5Press M.C. to select the primary color. R
6Turn M.C. to adjust the brightness level. Adjustment range: 0 to 60
# You cannot select a level below 10 for all three of
R (red), G (green), and B (blue) at the same time.
# You can also perform the same operation on other colors.
7Press M.C. and hold until CUSTOM ap- pears.
Using an AUX source
1Insert the stereo mini plug into the AUX input jack.
2Press SRC/OFF to select AUX as the source.
Note
AUX cannot be selected unless the auxiliary setting is turned on. For more details, refer to AUX (auxiliary input) on this page.
English
iPod/PANDORA when you turn on the engine. |
If you disconnect your USB storage device/ |
iPod, this unit’s source is turned off. |
OFF – When USB storage device/iPod is con- |
nected, the source is not switched to USB/ |
change the source to |
DORA manually. |
SW CONTROL (rear output and subwoofer set- ting)
DEMO (demo display setting)
1Press M.C. to turn the demo display on or off.
EVER SCRL (scroll mode setting)
When ever scroll is set to ON, recorded text information scrolls continuously in the display. Set to OFF if you prefer the information to scroll just once.
1Press M.C. to turn the ever scroll on or off.
Customizing the illumination color
1 | Press M.C. to display the main menu. |
2 | Turn M.C. to change the menu option |
and press to select ILLUMINATION. | |
3 | Turn M.C. to select the preset color or |
CUSTOM illumination color. | |
# You cannot create a custom illumination color | |
when SCAN is selected. | |
Turning the clock display on or off
%Press and hold TAG/
to turn the clock display on or off.
Note
The clock display disappears temporarily when you perform other operations, but the clock display appears again after 25 seconds.
Other Functions
Selecting the illumination color
This unit is equipped with
4 Press M.C. and hold until the customizing |
illumination color setting appears in the dis- |
play. |
En 11