
MANUAL
安裝手
Connecting the Units
Note:
• This unit is for vehicles with a |
and negative grounding. Before installing it in a |
recreational vehicle, truck, or bus, check the bat- |
tery voltage. |
• To avoid shorts in the electrical system, be sure |
to disconnect the · battery cable before begin- |
ning installation. |
• Refer to the owner’s manual for details on con- |
necting the power amp and other units, then |
make connections correctly. |
• Secure the wiring with cable clamps or adhesive |
tape. To protect the wiring, wrap adhesive tape |
around them where they lie against metal parts. |
• Route and secure all wiring so it cannot touch |
any moving parts, such as the gear shift, hand- |
brake and seat rails. Do not route wiring in |
places that get hot, such as near the heater outlet. |
If the insulation of the wiring melts or gets torn, |
there is a danger of the wiring |
the vehicle body. |
• Don’t pass the yellow lead through a hole into |
the engine compartment to connect to the battery. |
This will damage the lead insulation and cause a |
very dangerous short. |
• Do not shorten any leads. If you do, the protec- |
tion circuit may fail to work when it should. |
• Never feed power to other equipment by cutting |
the insulation of the power supply lead of the |
unit and tapping into the lead. The current capac- |
ity of the lead will be exceeded, causing over- |
heating. |
• When replacing fuse, be sure to use only fuse of |
the rating prescribed on the fuse holder. |
• Since a unique BPTL circuit is employed, never |
•When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp’s power terminal. Likewise, do not connect the blue/white lead to the power ter- minal of the
•To avoid
•To prevent incorrect connection, the input side of the
•If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be con- nected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehi- cle battery may be drained when you are away from the vehicle for several hours.
|
| CC |
|
|
|
|
|
|
|
|
| F | A | O |
|
|
| F | O |
|
|
|
| N |
| N | ||||||
O | F |
|
|
|
| O | F |
|
|
|
|
|
|
| S |
|
|
| S | ||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| T |
|
|
|
| T |
|
|
|
| R | A |
|
|
| R | A |
|
|
| T |
|
|
| T |
|
ACC position | No ACC position |
• The black lead is ground. Please ground this lead |
separately from the ground of |
ucts such as power amps. |
Connecting the power cord
This product
When you connect a power amp (sold separately), be sure to use the blue/white lead of this unit. If you use the blue/white lead of the head unit, it causes noises.
Blue/white
To system control terminal of the power amp or
Yellow | Fuse holder | |
To terminal always supplied with | ||
| ||
power regardless of ignition switch |
| |
position. |
| |
Black (ground) |
| |
To vehicle (metal) body. |
|
<ENGLISH>
Connecting to a sold separately power amp
This product can be connected to a sold separately power amp using the RCA output jacks.
System remote control
Blue/white
To system control terminal of the power amp or
This product | When you connect a power amp (sold | |
separately), be sure to use the blue/white | ||
| ||
| lead of this unit. If you use the blue/white | |
| lead of the head unit, it causes noises. |
|
| Rear output |
| ||
|
|
| |||
Front output | |||||
| Center output |

Subwoofer output
Power amp (sold separately)
Power amp (sold separately)
INSTALLATION
冊
This product conforms to new cord colors.
本產品適合於新型軟線顏色。
wire so the speaker leads are directly grounded or |
the left and right · speaker leads are common. |
• Speakers connected to this unit must be high- |
power types with minimum rating of 50 W and |
impedance of 4 to 8 ohms. Connecting speakers |
with output and/or impedance values other than |
those noted here may result in the speakers catch- |
ing fire, emitting smoke or becoming damaged. |
• When this product’s source is switched ON, a |
control signal is output through the blue/white |
lead. Connect to an external power amp’s system |
remote control or the car’s |
control terminal (max. 300 mA 12 V DC). If the |
car features a glass antenna, connect to the anten- |
na booster power supply terminal. |
If you ground the products together and the |
ground becomes detached, there is a risk of dam- |
age to the products or fire. |
• To ensure proper heat dissipation of this product, |
take special care not to block the cooling fan side |
of this product. |
• Cords for this product and those for other prod- |
ucts may be different colors even if they have |
the same function. When connecting this prod- |
uct to another product, refer to the supplied |
Installation manuals of both products and con- |
nect cords that have the same function.
|
|
| Black/white |
|
|
| + |
|
|
| ≠ |
|
|
| Black |
Left |
| White | Gray |
Front speaker | + | + | |
| ≠ | ≠ | |
|
| ||
|
| White/black | Gray/black |
|
| Green | Violet |
Rear speaker | + | + | |
| ≠ | ≠ | |
|
| ||
|
| Green/black | Violet/black |
Center speaker
Right
Front speaker
Rear speaker
| Power amp |
RCA cables | (sold separately) |
(sold separately) |
|
| Power amp |
| (sold separately) |
+ | + |
Front speaker | Front speaker |
≠ | ≠ |
+ | + |
Rear speaker | Rear speaker |
≠ | ≠ |
Printed in Japan 日本印刷
| <KMMUF/02B00000> |
Do not connect anything to the speaker leads that are not connected to speakers.
+ | + |
Center speaker | Subwoofer |
≠ | ≠ |