CONNECTIONS (CONNECTION PANEL)

CONNECTIONS

CONNECTION PANEL

1

2

3

4

5

6

7

8

 

 

 

SIGNAL GND

 

 

 

 

 

 

SIGNAL GND

 

 

 

DIGITAL IN

 

MASTER 2

REC

PHONO

LINE

PHONO

LINE

 

 

PHONO

CD

LINE

CD

 

 

 

 

L

 

 

L

 

L

 

 

 

L

 

 

L

 

 

 

 

POWER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF ON

 

 

CONTROL

 

 

CONTROL

 

 

CONTROL

 

CONTROL

 

 

MIDI OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1GND

 

 

R

 

R

 

 

 

R

 

 

R

 

DIGITAL OUT

 

R

 

 

 

 

 

 

 

 

 

fs (Hz)

 

2HOT

 

 

DIGITAL

 

 

DIGITAL

 

 

 

DIGITAL

 

DIGITAL

 

 

 

 

 

 

 

 

 

 

 

 

 

3COLD

 

 

LINE

 

 

LINE

 

 

 

CD

 

CD

48 k

96 k

 

AC IN

 

 

MASTER ATT -3dB0dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-6dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-12dB

 

 

 

 

 

 

 

 

 

 

 

 

R

MASTER 1 L

ADD

CUT

 

R

BOOTH

L

R

SEND L(MONO)

R RETURN L(MONO)

 

 

 

MIC SIGNAL

 

 

 

 

 

 

 

 

(TRS)

 

 

 

21

 

20

19

18

17

 

16

15

14

13

12

11

10

9

1.POWER switch2.MASTER 2 output connectors

RCA type unbalanced output.

3. Recording output connectors (REC)

RCA type output connectors for recording.

4. PHONO input connectors

RCA type phono level (MM cartridge) input connectors. Do not use for inputting line level signals.

5. LINE input connectors

RCA type line level input connectors.

Use to connect a cassette deck or other line level output component.

6. Signal grounding terminals (SIGNAL GND)

Use to connect ground wires from analog players.

This is not a safety grounding terminal.

7. CD input connectors

RCA type line level input connectors.

Use to connect a DJ CD player or other line level output component.

14. SEND output connectors

Ø6.3 mm phone-type output connectors.

Use to connect to the input connectors of external effectors or other similar components. When the L channel only is connected, a L+R monaural signal is output.

15. CONTROL connectors

Ø3.5 mm mini-connector. Use to connect to the control connector of a Pioneer DJ CD player.

When the connectors are connected, the DJM-800’s fader can be used to perform start/stop on the DJ CD player.

16. BOOTH monitor output connectors

Ø6.3 mm phone-type booth monitor output connectors.

The sound level from these connectors is controlled independently by the BOOTH MONITOR level dial, regardless of the position of the MASTER LEVEL dial. (These connectors are TRS output, so they support both balanced and unbalanced outputs.)

17. DIGITAL/LINE input selector switches

Use to select either analog input (LINE) or digital input (DIGITAL IN).

8. DIGITAL IN connectors

RCA type digital coaxial input connectors.

Use to connect to DJ CD player or other digital coaxial output connectors.

÷The sound may be temporarily interrupted when the output signal’s sampling frequency is changed.

9. MIDI OUT connector

DIN type output connector.

Use to connect to other MIDI component (see P. 20).

10. DIGITAL OUT connector

RCA type digital coaxial output connector.

Master audio digital output.

11. Sampling frequency selector switch (fs 48 k/96 k)

Use to set the sampling frequency of the digital output to 96 kHz/24- bit format or 48 kHz/24-bit format.

÷Turn power off before changing this switch position.

12. DIGITAL/CD input selector switches

Use to select either analog input (CD) or digital input (DIGITAL IN).

18. Master output attenuator switch (MASTER ATT)

Use to attenuate the level of the master 1 and master 2 outputs. Selectable values are 0 dB, –3 dB, –6 dB and –12 dB.

19. Microphone signal switch(MIC SIGNAL ADD/CUT)

When set to the [ADD] position, the sounds from microphone 1 and microphone 2 are output to the BOOTH monitor output connectors. When set to the [CUT] position, the sounds from microphone 1 and microphone 2 are not output to the BOOTH monitor output connectors.

20. MASTER 1 output connectors

XLR type (male) balanced output.

÷When using a cord with RCA-type plug, users are recommended to connect the plug directly to the MASTER 2 connectors without using an XLR/RCA converter plug.

21. Power inlet (AC IN)

Use the accessory power cord to connect to an AC power outlet of the proper voltage.

13. RETURN connectors

Ø6.3 mm phone-type input connectors.

Use to connect to the output connectors of external effectors or similar components.

When the L channel only is connected, the L channel input is simultaneously input to the R channel.

5