OTHER (TROUBLESHOOTING)
TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunctions. If you think there is something wrong with this component, check the points below. Sometimes the trouble may originate from another component. Thus, also check the other electrical appliances also in use.
If the trouble cannot be rectified even after checking the following items, contact your dealer or nearest PIONEER service center.
Symptom |
| Probably cause |
|
|
| Remedy |
|
|
|
|
|
|
| ||||
No power | ÷ | Power cord isn’t connected. | ÷ | Connect power cord to outlet. | ||||
|
|
|
|
|
|
| ||
No sound, or too low | ÷ | Connection cords are loose or aren’t con- | ÷ | Connect properly. |
|
| ||
|
| nected properly. |
|
|
|
|
|
|
| ÷ | Connector terminals and plugs are dirty. | ÷ | Wipe away dirt and soil. |
|
| ||
| ÷ | Input level is set too low. | ÷ | Rotate INPUT LEVEL dial toward right | ||||
|
|
|
|
| ([MAX] direction). |
|
| |
|
|
| ÷ | Try setting IN&OUT LEVEL switch to the | ||||
|
|
|
|
| opposite position. |
|
| |
| ÷ | Effect output level is set too low. | ÷ | Rotate EFFECT OUT LEV. dial toward right | ||||
|
|
|
|
| ([MAX] direction). |
|
| |
|
|
|
|
| ||||
Analog inputs aren’t output | ÷ | A digital or EFX LINK input is connected. | ÷ | Cancel the EFX LINK, and disconnect any | ||||
|
| When analog and digital inputs are connected |
|
| digital input with priority over analog | |||
|
| simultaneously, the digital input is given |
|
| inputs. |
|
|
|
|
| priority. |
|
| The order of priority of inputs is: | |||
| ÷ | The DJ mixer |
|
| EFX LINK > Digital input > Analog input. | |||
|
| LINK has its effecter link set to ON (EFX LINK). |
|
|
|
|
|
|
|
|
|
|
| ||||
Digital signals aren’t output. | ÷ | EFX LINK is connected to DJ mixer (DJM- | ÷ | If EFX LINK is connected to DJ mixer (DJM- | ||||
|
| 1000) via digital link cable. |
|
| 1000) via digital link cable, ordinary digital | |||
|
|
|
|
| signals are not output. |
|
| |
|
|
|
|
| Disconnect the digital link cable. | |||
| ÷ | The digital output fs setting does not match | ÷ | Set the digital output fs to match the | ||||
|
| the connected component. |
|
| connected component. |
|
| |
|
|
|
|
| ||||
When set to BYPASS, analog | ÷ | No analog inputs are connected. | ÷ | Use analog signals for input. Or use digital | ||||
signals aren’t output. |
| Even if a digital input or EFX LINK is |
|
| output. Outputs when BYPASS is selected | |||
|
| connected, analog inputs are output as analog |
|
| are as follows: |
|
| |
|
| during BYPASS mode. |
|
| Input |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |
|
|
|
|
| connection | Analog output | Digital output | |
|
|
|
|
| conditions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Analog only | Analog source | Analog source | |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Digital only | (no output) | Digital source | |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Analog & | Analog source | Digital source | |
|
|
|
|
| digital | |||
|
|
|
|
|
|
|
| |
|
|
|
|
| ||||
Effect sounds aren’t applied. | ÷ | The lever switch is set to [OFF]. | ÷ | Either hold lever switch in [ON] position, or | ||||
|
|
|
|
| set to [ON/LOCK]. |
|
| |
| ÷ | MIX dial is set to [MIN]. | ÷ | Rotate MIX dial toward the right ([MAX] | ||||
|
|
|
|
| direction). |
|
|
|
| ÷ | DEPTH dial is set to [MIN]. | ÷ | Rotate DEPTH dial toward the right ([MAX] | ||||
|
|
|
|
| direction). |
|
|
|
| ÷ | EFFECT OUT LEV. dial is set to [MIN]. | ÷ | Rotate EFFECT OUT LEV. dial toward the | ||||
|
|
|
|
| right ([MAX] direction). |
|
| |
| ÷ | BYPASS button is ON. | ÷ | If BYPASS indicator is flashed, no effects | ||||
|
|
|
|
| will be output. Press BYPASS so that the | |||
|
|
|
|
| indicator goes out. |
|
| |
| ÷ | EFFECT FREQUENCY indicators (HI, MID, | ÷ | If EFFECT FREQUENCY indicators are all off, | ||||
|
| LOW) are all off (during use of TRANS, |
|
| only the original sound will be output. Press | |||
|
| FLANGER, FILTER, or PHASER effects). |
|
| the button corresponding to the frequency | |||
|
|
|
|
| band to which you wish to apply effects (the | |||
|
|
|
|
| button’s indicator will light). |
|
| |
| ÷ | Some combinations of effects may have weak | ÷ | Try setting SIGNAL FLOW switch to the | ||||
|
| results. Particularly, some combinations of |
|
| opposite position (reverse order of signal | |||
|
| beat effects and digital jog break may sound |
|
| processing for beat effects and digital jog | |||
|
| weak. |
|
| break). |
|
|
|
|
|
|
|
| ||||
No effect sound is heard when | ÷ | EFFECT FREQUENCY indicators (HI, MID, LOW) | ÷ | If EFFECT FREQUENCY indicators are all off, | ||||
beat effects are applied. |
| are all off (during use of DELAY, ECHO, PITCH |
|
| no effect sound will be output. Press the | |||
|
| ECHO effects). |
|
| button corresponding to the frequency band | |||
|
|
|
|
| to which you wish to apply effects (the | |||
|
|
|
|
| button’s indicator will light). |
|
| |
|
|
|
|
|
|
|
|
|
25