![](/images/new-backgrounds/1242806/2428063x1.webp)
Before You Start
Before You Start
Before You Start
Before You Start
Important
The serial number of this device is located on the bottom of this unit. For your own security and convenience, be sure to record this num- ber on the enclosed warranty card.
Resetting the microproces- sor
The microprocessor must be reset under the following conditions:
•Prior to using this unit for the first time after installation
•If the unit fails to operate properly
•When strange or incorrect messages appear on the display
Press RESET on the unit with a pen tip or other pointed instrument.
RESET button
Precautions
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio com- munications. However, there is no guar- antee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
Information to User
Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.
•Keep this manual handy as a reference for operating procedures and precautions.
•Always keep the volume low enough so you can hear sounds outside of the car.
•Protect this product from moisture.
•If the battery is disconnected or discharged, the preset memory will be erased and must be reprogrammed.
After-sales service for Pioneer products
Please contact the dealer or distributor from where you purchased this unit for
Please do not ship your unit to the company at the addresses listed below for repair with- out advance contact.
U.S.A.
Pioneer Electronics (USA), Inc.
CUSTOMER SUPPORT DIVISION P.O. Box 1760
Long Beach, CA
For warranty information please see the Limited Warranty sheet included with this unit.
Product registration
Visit us at the following site:
1Register your product. We will keep the details of your purchase on file to help you refer to this information in the event of an
insurance claim such as loss or theft.
2Receive updates on the latest products and technologies.
3Download owner’s manuals, order prod- uct catalogues, research new products, and much more.
Operating with different head units
Operate this unit (for XM reception) with the connected head unit. For illustration, instruc- tions in this manual use the
•When using a remote control, you can operate these head units marked with * in the same way as the
Head unit group 1
Operation when using the following head unit is the same as with the
Head unit group 2
When using this unit with these head units, operate while referring to the head unit group 2 function compatibility chart.
•These head units control this unit as an external unit.
Head unit group 3
When using this unit with these head units, operate while referring to the head unit group 3 function compatibility chart.
Function compatibility charts
Operate using the same buttons on the head unit itself or the remote control.
Head unit group 2
Function | Button | Operation |
|
|
|
Source switching | SOURCE | :Select |
|
|
|
Select the channel | or | :Select |
|
|
|
Changing the band | BAND | :Select |
|
|
|
Preset memory | :Memory | |
| (hold for 2 |
|
| seconds) |
|
|
|
|
Direct recall | :Recall | |
|
|
|
Sequential recall | or | :Recall |
(Channel number |
|
|
select mode) |
|
|
|
|
|
Select the category | or | :Select |
(Channel category |
|
|
select mode) |
|
|
|
|
|
Entering the | FUNCTION | :Select |
function menu |
|
|
(See “Introduction |
|
|
of advanced tuner |
|
|
operation”.) |
|
|
|
|
|
Switching the | or | :Select |
display (FUNC1) |
|
|
|
|
|
Scrolling the | or | :Scroll |
display (FUNC1) | (hold for 2 |
|
| seconds) |
|
|
|
|
Scrolling the | DISPLAY | :Scroll |
display | (hold for 2 |
|
| seconds) |
|
|
|
|
Switching the | or | :Select |
channel select |
|
|
mode (FUNC2) |
|
|
|
|
|
Head unit group 3
Function | Button | Operation | |
|
|
| |
Source switching | SOURCE | :Select | |
|
|
|
|
Select the channel |
| or | :Select |
|
|
| |
Changing the band | BAND | :Select | |
|
|
| |
Switching the | DISPLAY | :Select | |
display |
|
|
|
|
|
| |
Scrolling the | DISPLAY | :Scroll | |
display | (hold for 2 |
| |
| seconds) |
| |
|
|
| |
Display the MENUS | A.MENU | :Display | |
|
|
|
|
Preset memory | 1. | or | :Select number |
(P.CH MEMORY) | 2. A.MENU | :Memory | |
|
|
|
|
Direct recall | 1. | or | :Select number |
(P.CH RECALL) | 2. A.MENU | :Recall | |
|
|
|
|
Switching the |
| or | :Select |
channel select |
|
|
|
mode (CH MODE) |
|
|
|
|
|
|
|
Select the category |
| or | :Select |
(Channel category |
|
|
|
select mode) |
|
|
|
|
|
|
|
En | En | En | En |