OSD (On Screen Display) Controls
English
WIDE Operations
10
SCREEN SIZE Operation with Computer Signals
Switch to the wide screen mode to expand the 4 : 3 image to fill the entire screen.
1.Press the SCREEN SIZE button on the remote control.
2.Within 3 seconds ...
Press the SCREEN SIZE button again. The screen size switches as follows:
Α 4:3 Α FULL Α ZOOM
4:3 size screen (4:3 or SXGA 5:4)
The picture has the same size as the normal computer image.
FULL size screen
The image is expanded in the horizontal direction.
ZOOM size screen
When wide signals are input.
FULL size screen
When “PICTURE SIZE” is set to “OFF”
*This cannot be set in some models. “DOT BY DOT” will not be displayed in such cases.
The screen size switches as follows:
ΑD BY D Α FULL Α ZOOM
DOT BY DOT screen (VGA, SVGA 4:3)
The image is dot by dot resolution.
FULL size screen
The image is expanded in the horizontal and vertical direction.
ZOOM size screen
When wide signals are input.
FULL
DOT BY DOT
The image is dot by dot resolution.
*“D BY D” can be switched only when a 1280 dot 768 line signal is input.
Information
Supported resolution
See page 30 for details on the display output of the various VESA signal standards supported by the monitor.
“PICTURE SIZE” setting
When the setting of “PICTURE SIZE” is OFF, the size of
When 852 (848) dot 480 line wide VGA* signals with a vertical frequency of 60 Hz and horizontal frequency of 31.7 (31.0) kHz are in- put
Select an appropriate setting for RGB SELECT mode referring to the“Table of Signals Supported” on page 30.
*“VGA”, “SVGA” and “SXGA” are registered trademarks of IBM, Inc. of the United States.
Note:
Do not allow the displayed in 4:3 mode for an extended period. This can cause a phosphor
Menu Operations
The OSD window is displayed with respect to the screen as shown on the diagram.
*Depending on the screen’s mode, the OSD may be displayed differently.
In the explanation, the OSD section is shown close up.
|
|
|
| MAIN MENU | 1 / 2 |
| ||
| PICTURE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SOUND |
|
|
|
|
|
|
|
| SCREEN |
|
|
|
|
|
|
|
| OPTION1 |
|
|
|
|
|
|
|
| ADVANCED OSD | : | OFF |
| ||||
| NEXT PAGE |
|
|
|
|
| ||
| SEL. |
| MENU | OK | EXIT | EXIT |
| |
|
|
|
|
|
|
|
|
|
The following describes how to use the menus and the selected items.
1.Press the MENU/SET button on the remote control to display the MAIN MENU.
|
|
| MAIN MENU | 1 / 2 | |
| PICTURE |
|
|
|
|
| SOUND |
|
|
| |
| SCREEN |
|
|
| |
| OPTION1 |
|
|
| |
| ADVANCED OSD | : | OFF | ||
| NEXT PAGE |
|
| ||
| SEL. | MENU OK | EXIT EXIT | ||
|
|
|
|
| |
|
|
| MAIN MENU | 2 / 2 | |
| PREVIOUS PAGE |
|
| ||
| LANGUAGE |
|
|
| |
| COLOR SYSTEM |
|
| ||
| SOURCE INFORMATION |
|
| ||
| SEL. | MENU OK | EXIT EXIT | ||
|
|
|
|
|
|
2.Press the cursor buttons ▲ ▼ on the remote control to highlight the menu you wish to enter.
3.Press the MENU/SET button on the remote control to select a sub menu or item.
|
|
| PICTURE |
| 1 / 2 | ||
| CONTRAST |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| BRIGHTNESS |
|
|
|
|
| |
| SHARPNESS |
|
|
|
|
| |
|
|
|
|
|
| ||
| COLOR |
|
|
|
|
| |
| TINT |
|
|
|
|
| |
| AV SELECTION |
|
|
|
|
| |
|
| : | STD | ||||
| DNR |
| : | OFF | |||
| NEXT PAGE |
|
|
|
|
| |
| SEL. | ADJ. | EXIT RETURN | ||||
|
|
|
|
|
|
|
|
4.Adjust the level or change the setting of the selected item by using the cursor buttons on the remote control.
5.The adjustments or the settings that are stored in memory. The change is stored until you change it again.
6.Repeat steps 2 – 5 to adjust an additional item, or press the EXIT button on the remote control to return to the main menu.
* When adjusting using the bar at the bottom of the screen, press the or button within 5 seconds. If not, the current setting is set and the previous screen appears.
Note: The main menu disappears by pressing the EXIT button.
Information
Advanced menu mode
When “ADVANCED OSD” is set to “ON” in the main menu (1/2), full menu items will be shown.
| MAIN MENU | 1 / 2 |
PICTURE |
|
|
SOUND |
| |
SCREEN |
| |
OPTION1 |
| |
OPTION2 |
| |
OPTION3 |
| |
ADVANCED OSD | : ON | |
NEXT PAGE |
| |
SEL. | MENU OK | EXIT EXIT |
Setting the language for the menus
The menu display can be set to one of seven languages.
Example: Setting the menu display to “DEUTSCH”
On “MAIN MENU”, select “LANGUAGE”, then press the MENU/SET button.
The “LANGUAGE” screen appears.
On “LANGUAGE”, select “ DEUTSCH”, then press the MENU/SET button.
LANGUAGE
LANGUAGE
:
DEUTSCH 
ADJ. MENU OK | EXIT RETURN |
The “LANGUAGE” is set to “DEUTSCH” and return to the main menu.
Information
Language settings
ENGLISH ........ | English | ITALIANO ........ | Italian |
DEUTSCH ....... | German | SVENSKA ....... | Swedish |
FRANÇAIS ...... | French | ................ | Japanese |
ESPAÑOL ....... | Spanish |
|
|
English
OSD (On Screen Display) Controls
11
En | En |