Important Information
English
Important Informationi2
Precautions
Please read this manual carefully before using your plasma monitor and keep the manual handy for future reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO
This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside of this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.
WARNINGTO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT’S POLARIZED PLUG WITHAN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE
Warning
Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/ Data Processing Equipment ANSI/NFPA 75.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio / TV technician for help.
Warnings and Safety Precaution
This plasma monitor is designed and manufactured to provide long,
The plasma display panel consists of fine picture elements (cells) with more than 99.99 percent active cells. There may be some cells that do not produce light or remain lit.
For operating safety and to avoid damage to the unit, read carefully and observe the following instructions. To avoid shock and fire hazards:
1.Provide adequate space for ventilation to avoid internal heat
If you install the unit in an enclosure, make sure there is adequate space at the top of the unit to allow hot air to rise and escape. If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens, turn off the power to the monitor and unplug the power cord. If the room where the monitor is installed is particularly hot, move the monitor to a cooler location, and wait for 60 minutes to cool the monitor. If the problem persists, contact your dealer for service.
2.Do not use this unit’s polarized plug with extension cords or outlets unless the prongs can be completely inserted.
3.Do not expose the unit to water or moisture.
4.Avoid damage to the power cord, and do not attempt to modify the power cord.
5.Unplug the power cord during electrical storms or if the unit will not be used over a long period.
6.Do not open the cabinet which has potentially dangerous high voltage components inside. If the unit is damaged in this way the warranty will be void. Moreover, there is a serious risk of electric shock.
7.Do not attempt to service or repair the unit. The manufacturer is not liable for any bodily harm or damage caused if unqualified persons attempt service or open the back cover. Refer all service to authorized Service Centers.
NOTE:
When you connect a computer to this monitor, use an RGB cable including the ferrite core on both ends of the cable. And regarding DVI and power cable, attach the supplied ferrite cores. If you do not do this, this monitor will not conform to mandatory FCC standards.
Attaching the ferrite cores:
Set the ferrite cores on both ends of the DVI cable (not supplied), and both ends of the power cable (supplied). Close the lid tightly until the clamps click.
Use the band to fasten the ferrite core (supplied) to the DVI cable.
DVI cable (not supplied) |
|
|
|
|
|
| ||||
|
|
|
| band | band | Connector | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| |||
|
| core (small) | core | (small) | ||||||
Power cable (supplied)
core (large)
core (large)
To avoid damage and prolong operating life:
1.Use only with
2.Handle the unit carefully when installing it and do not drop.
3.Set the unit away from heat, excessive dust, and direct sunlight.
4.Protect the inside of the unit from liquids and small metal objects. In case of accident, unplug the power cord and have it serviced by an authorized Service Center.
5.Do not hit or scratch the panel surface as this causes flaws on the surface of the screen.
6.For correct installation and mounting it is strongly recommended to use a trained, authorized dealer.
7.As is the case with any
8.To avoid sulfurization it is strongly recommended not to place the unit in a dressing room in a public bath or hot spring bath.
9.Do not use in a moving vehicle, as the unit could drop or topple over and cause injuries.
10.Do not place the unit on its side,
Plasma monitor cleaning procedure:
1.Use a wiping cloth (attached) or a soft dry cloth to clean the front panel and bezel area. Never use solvents such as alcohol or thinner to clean these surfaces.
2.Clean plasma ventilation areas with a vacuum cleaner with a soft brush nozzle attachment.
3.To ensure proper ventilation, cleaning of the ventilation areas must be carried out monthly. More frequent cleaning may be necessary depending on the environment in which the plasma monitor is installed.
Recommendations to avoid or minimize phosphor
Like all
*Always enable and use your computer’s screen saver function during use with a computer input source.
*Display a moving image whenever possible.
*Change the position of the menu display from time to time.
*Always power down the monitor when you are finished using it.
If the plasma monitor is in long term use or continuous operation take the following measures to reduce the likelihood of phosphor burn:
*Lower the Brightness and Contrast levels as much as possible without impairing image readability.
*Display an image with many colors and color gradations (i.e. photographic or
*Create image content with minimal contrast between light and dark areas, for example white characters on black backgrounds. Use complementary or pastel color whenever possible.
*Avoid displaying images with few colors and distinct, sharply defined borders between colors.
* Note:
Contact your dealer for other recommended procedures that will best suit your particular application needs.
CAUTION:WHEN POSITIONING THIS EQUIPMENT ENSURE THAT THE MAINS PLUG AND SOCKET IS EASILY ACCES- SIBLE.
Information to UserAlteration or modifications carried out without appropriate authorization may invalidate the user's right to operate the equipment.
WARNING:Handling the cord on this product or cords associated with accessories sold with the product will expose you to lead, a chemical known to the State of California and other governmental entities to cause cancer and birth defects or other reproductive harm. Wash hands after
handling.English
Important Information
ii3
En | En |