Installation
You can attach your optional mounts or stand to the plasma monitor in one of the following two ways: * While it is upright. (See Drawing A)
English | * As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the |
| |
| monitor when it was packaged, beneath the screen surface so as not to scratch the screen face. |
| * Do not touch or hold the screen face when carrying the unit. |
•This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (Wall mount unit, Stand, etc.)
* See page 1.•For correct installation and mounting it is strongly recommended to use a trained, authorized dealer.
Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer.
Product warranty does not cover damage caused by improper installation.* Use only the mounting kit or stand provided by manufacturer and listed under Options.
Drawing A |
| Drawing B |
| When installing or carrying, use the | |||
|
|
|
| handles attached to the upper back | |||
|
|
|
| of the display. | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Creating a video wall
With |
| English | ||||
• Connect signal cables and remote cables as shown below. |
|
|
| |||
|
|
|
| |||
Video signal |
|
| PC/COMPONENT signal |
|
| |
|
|
|
| BNC connector |
|
|
| BNC connector | OUT | PC signal/ | IN |
|
|
|
| VIDEO signal | COMPONENT |
|
|
|
IN | RCA phono plug |
| signal |
|
|
|
VIDEO signal |
|
|
|
|
|
|
|
|
|
| OUT | PC signal/ |
|
|
|
|
| COMPONENT |
| |
|
|
|
|
|
| |
Remote IN |
|
|
|
| signal |
|
control |
| OUT Remote |
|
|
|
|
|
| Remote IN |
|
| ||
|
| control |
|
| ||
|
|
| control | OUT Remote |
| |
|
|
|
|
| ||
|
|
|
|
| control |
|
Note: |
|
|
|
|
|
|
1. The VIDEO1 and PC1 terminals can be used for either INPUT or OUTPUT. |
|
| ||||
When LOOP OUT is ON, do not connect an OUTPUT signal from another unit, that will place an extraordinary load on |
| |||||
the other unit and may damage it. |
|
|
|
|
| |
2.LOOP OUT can not be turned ON while signals are input to the PC1 terminal.
3.LOOP OUT can be turned ON while signals are input to the PC1 terminal if the POWER is switched ON.
Information•To loop signals out to another plasma display, set the LOOP OUT to ON.
•To create a video wall, set the VIDEO WALL menu items properly.
•To connect monitors, please use a 1~2m (3.3~6.6 feet) BNC cable (any commercially available cable).
•If the image quality is poor, do not use the monitor’s out terminal. Use a distribution amplifier (any commercially available distribution amplifier) to connect the split signals to the respective monitor INPUT terminals.
•Being used as a video wall function, maximaly
•A distribution amplifier is particularly recommended when using
•From the second monitor onward, connections require a
Ventilation Requirements for enclosure mounting
To allow heat to disperse, leave space between surrounding objects as shown on the diagram below when installing.
|
|
|
|
|
|
| Wall |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
50mm (2") |
|
|
|
|
| 50mm (2") |
|
|
| (2") | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |||
50mm | Wall | ||
|
|
| |
|
|
|
|
|
|
|
|
How to use the safety metal fittings and the screws for safety metal fittings
These are fittings for fastening the unit to a wall to prevent tipping due to external shock when using the stand (optional). Fasten the safety fittings to the holes in the back of the monitor using the safety fitting mount screws.
Screw hole
Screw or Hook etc. (Not supplied)
Cable Management
Using the cable clamps provided with the plasma display, bundle at the back of the unit the signal and audio cables connected to the display.
To attach
1.2.
clamp
Back of the unit
mounting holes
To detach
Installation
50mm (2") (2")mm 50
Safty metal fittings
Wall
Metal chain (Not supplied)
cables
mounting hole
Table Top
2
3
En | En |