Pioneer VSX-01THX Controlling the rest of your system, Selecting preset codes directly

12Controlling the rest of your system

Chapter 12:

Controlling the rest of your system

Setting the remote to control other components

Most components can be assigned to one of the input source buttons (such as DVD or CD) using the component’s manufacturer preset code stored in the remote.

However, there are cases where only certain functions may be controllable after assigning the proper preset code, or the codes for the manufacturer in the remote control will not work for the model that you are using.

Note

•You can cancel or exit any of the steps by pressing RECEIVER. To go back a step, press RETURN.

•After one minute of inactivity, the remote automatically exits the operation.

Selecting preset codes directly

	ST	ENTER	ST
RECEIVER	SOURCE
	CATEGORY		RETURN

3Use the number buttons to enter the 3 digit preset code (see below).

The indicator blinks for half a second after you input each digit and shows a long, two second blink once you have entered a valid code. If the LED blinks three times, it means an invalid code has been input or an error has occurred.

4Repeat steps 1 through 3 for the other components you want to control.

5When you’re done, press RECEIVER.

To try out the remote control, switch the component on or off (into standby) by pressing SOURCE. If it doesn’t seem to work, select the next code from the list (if there is one).

Preset code list

You should have no problem controlling a component if you find the manufacturer in this list, but please note that there are cases where codes for the manufacturer in the list will not work for the model that you are using. There are also cases where only certain functions may be controllable after assigning the proper preset code.

DVD	BD	TV	HDMI		SETUP TUNE
				iPod CTRL
DVR 1	DVR 2	CD	CD-R	AUTO/	STEREO/		BD MENU
						STANDARD
				DIRECT	A.L.C.		ADV SURR
FM/AM	XM	SIRIUS	iPod USB	HDD	DVD
				THX	STATUS		PHASE
INPUT			DIMMER
SELECT
1		2	3	ANT		MPX	SIGNAL SEL
GENRE	MCACC		SLEEP				MEM
4		5	6	AUDIO	DISPLAY	CH
SR+	SBch		A.ATT
7		8	9	TV CTRL		RECEIVER
D.ACCESS CH LEVEL			CLASS

0ENTER

INPUT	MASTER	MAIN	ZONE 2
	VOLUME

1While pressing the RECEIVER button, press SETUP. The indicator on the remote control blinks.

2Press the input source button for the component you want to control.

When assigning preset codes to TV CONTROL, press TV CTRL here.

The indicator lights up.1

DVD

Manufacturer Code AKAI 007 DENON 003, 010 GOLDSTAR 014 HITACHI 012

JVC 004 LOEWE 013

MICROSOFT 017 (video game) PANASONIC 003, 019 PHILIPS 013

PIONEER 000, 003, 009, 018, 020, 021 (BDP), 023 (BDP)

RCA 008, 011

SAMSUNG 005

SHARP 006

SONY 002, 016 (video game) THOMSON 015 TOSHIBA 001, 022 (HD DVD) ZENITH 014

LD

Manufacturer Code

KENWOOD 103

MITSUBISHI 100

PANASONIC 105, 106

PHILIPS 104

PIONEER 100, 111

RCA 107

SONY 101

SAT

Manufacturer Code

BELL 208

ECHOSTAR 205

PIONEER 200, 210

PRIMESTAR 206

RCA 201, 203, 209

SONY 202

CD

Manufacturer Code California Audio labs 304 DENON 309

JVC 303

KENWOOD 310, 311, 321 KODAK 322

MARANTZ 304, 312, 323, 324 MCS 304

MEMOREX 300

NAD 316

ONKYO 307, 308, 320 OPTIMUS 300 PANASONIC 304, 326 PHILIPS 312, 322 PIONEER 300, 348 (SACD) QUASAR 304

RCA 302, 313, 319 SANYO 313

SONY 301, 316, 317, 318 TEAC 305, 306, 324, 325, 327 THOMSON 319 YAMAHA 314, 315, 328

Note

1 You can’t assign the RECEIVER, FM/AM, iPod USB, XM or SIRIUS buttons.

78

En