CABLE TV RECEPTION
CONNECTION PROCEDURES
Connect your equipment as shown in the figures on page 6. Use the first table if you are only connecting the
STEP | ACTION | |
1 | Connect cable service to | |
CABLE IN (input connector). | ||
| ||
| ¦ If TV has video and stereo audio | |
| inputs: | |
| Follow the Stereo Connection | |
| diagram on page 6. Connect BD- | |
| V1000 L/R AUDIO OUT and VIDEO | |
| OUT to the corresponding IN jacks | |
| on the TV, using shielded RCA | |
| (phono) jumper cables. | |
| If TV VIDEO IN is a | |
| jack, connect | |
2 | OUT to TV | |
special | ||
| Leave | |
| unconnected. | |
| ¦ If TV has no video/audio inputs: | |
| Follow the Simple Connection | |
| diagram on page 6. Connect BD- | |
| V1000 TO TV (output) connector to | |
| the TV VHF ANTENNA INPUT. | |
| If TV VHF ANTENNA INPUT is a | |
| ||
| screws), then use a 75 ohm - 300 | |
| ohm adapter. | |
3 | Plug TV AC cord into | |
outlet. | ||
| ||
4 | Plug | |
outletthatisnotcontrolledbyaswitch. | ||
| ||
|
|
If you have a VCR, follow the procedure below to connect it between the
STEP | ACTION | |
|
| |
| Follow the VCR Connection | |
1 | diagram on page 6. Connect cable | |
service to | ||
| ||
| (input connector). | |
|
| |
| Connect | |
2 | inputs using the same criteria and | |
procedures as in step 2 of the table | ||
| ||
| above for TV connection. | |
|
| |
3 | Connect the VCR outputs to the TV | |
inputs, again using the same | ||
| criteria and procedures. | |
|
| |
4 | Connect TV AC cord to | |
AC outlet. | ||
| ||
|
| |
| Connect VCR and | |
5 | cords to AC outlets that are not | |
| controlled by a switch. | |
|
|
NOTE:
When disconnecting the
SETTING UP THE TV
Follow the steps in the table to set up your TV for cable.
STEP |
|
| ACTION |
| ||
|
|
|
|
|
| |
| ¦ If | you | used | the | Simple | |
| Connection method: |
| ||||
| Tune TV to channel 3 or 4. | |||||
| Other documentation that came | |||||
1 | with your | |||||
how to switch the | ||||||
| ||||||
| output channel between 3 and 4. | |||||
| ¦ If you used the Stereo or VCR | |||||
| Connection method: |
| ||||
| Select | the A/V | (Audio/Video) | |||
| input setting on your TV. | |||||
|
| |||||
| Use your remote control’s TV | |||||
| POWER button to turn the TV on | |||||
| and off. |
|
|
| ||
| Exception: |
|
| |||
| TV sets without remote control can | |||||
2 | be turned on through the BD- | |||||
V1000. Leave the TV power switch | ||||||
| ||||||
| on. Use the | |||||
| change the | |||||
| UNSWITCHED to SWITCHED. Use | |||||
| the |
| panel or | |||
| remote control POWER button to | |||||
| turn the TV on and off. |
|
TURNING OFF THE BD-V1000
To turn off the
You can use your remote’s TV POWER button to turn TV on/off if you have set up the remote with the correct TV code.
VCR RECORDING
The
7
<BRB1050>