Manuals / Brands / Computer Equipment / Switch / Planet Technology / Computer Equipment / Switch

Planet Technology 10/100/1000Mbps Gigabit Ethernet Web-manageable Switch, GSW-1402S 4.5 VLAN Page, 4.5.1 VLAN Static List, 4.5.1.1 To Create A New VLAN Group, 4.5.1.2 To Remove A VLAN Group, 4.5.1.3 To Modify A VLAN Group

1 29

Download 29 pages, 579.16 Kb

4.5 VLAN Page

There are three tabs in VLAN Page: VLAN Static List, VLAN Static Table, and VLAN Port Configuration. Please refer to section 3.5.2 IEEE802.1Q TAG VLAN for further details.

4.5.1 VLAN Static List

This screen is used to Add / Remove / Modify VLAN and up to 255 groups. The VLAN groups that have been created are all listed here.

4.5.1.1 To Create A New VLAN Group

1.Specify the name for the new VLAN group (VLAN name is only used for identification).

2.Enter a number (VLAN ID) for the new VLAN group.

3.Check the “Active” box to activate the VLAN or leave it blank and activate it afterward.

4.Click <<Add button to create the new VLAN.

4.5.1.2 To Remove A VLAN Group

1.Select a VLAN group you want to remove from the “Current” list.

2.Click Remove>> button to remove it.

Note: 1. If a removed port is no longer belong to any other group, it is temporarily disabled because no one can communicate with it.

2.If one port’s PVID is equal to this VLAN ID, removing this VLAN group will not allow until you change it.

4.5.1.3 To Modify A VLAN Group

1.Select a VLAN group you want to remove from the current list

2.Modify parameters in “New” column

3.Click Modify button to submit the new parameters

4.5.2 VLAN Static Table

This screen is used to Add/Remove member ports of a VLAN.

19

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning Revision TABLE OF CONTENTS APPENDIX A Chapter 1 INTRODUCTION 1.1 Checklist 1.2 About the Switch 1.3 Features 1.4 Specifications Chapter 2 Hardware Description 2.1Front Panel 2.2 Rear Panel 2.3Hardware Installation 2.3.1 Connecting end node or hub or switch 2.3.2 Connecting to Network Backbone or Server Chapter 3 Console management 3.1 Connect To PC 3.2 Main Menu 3.3 System Menu 3.3.1 System Information 3.3.2 System Configuration 3.4 Management Setup Menu 3.4.1 Network Configuration 3.4.2 Console Port Status Display 3.4.3 Management Features Control 3.4.3.1 Web-basedCapability 3.5 Device Control Menu 3.5.1 Port Status/Configuration 3.5.2 IEEE802.1Q TAG VLAN 3.5.2.1 VLAN Port Configuration 3.5.2.2 VLAN Table Status 3.5.2.3 VLAN Static Entry Created 3.5.2.4 VLAN Static Entry Modification 3.5.2.5 VLAN Static Entry Delete 3.5.3 Mirror 3.5.3.1 Mirror Function 3.5.3.2 Choose Sniffer Port 3.5.3.3 Choose Monitored Port 3.5.4 Port Aggregation 3.6User Authentication Menu 3.7 System Utility Menu 3.7.1 System Restart 3.7.2 Default Factory Reset 3.7.3 Timeout Interval Setup 3.7.4 TFTP Download 3.7.4.1 Modify Download Filename 3.7.4.2 Modify TFTP Server IP 3.7.5.1 Modify Ping Count 3.7.5.2 Modify Ping Target IP 3.7.5.3 Start Ping 3.7.6 Search Location by Port Name 3.8 Save Runtime Configuration 4. Web management 4.1 Start A Web Browser Session 4.2 Main Page 4.2.1 Save 4.2.2 Default 4.2.3 Reboot 4.2.4 Ping 4.2.5 Telnet 4.3 System Page 4.4 Port Page 4.4.1 Port Setting Duplicate 4.5 VLAN Page 4.5.1 VLAN Static List 4.5.1.1 To Create A New VLAN Group 4.5.1.2 To Remove A VLAN Group 4.5.1.3 To Modify A VLAN Group 4.5.2.1 To Add Member Ports 4.5.2.2 To Remove Member Ports 4.5.3VLAN Port Configuration 4.5.3.1 To Change The PVID 4.6 Port Aggregation Page 4.7 Mirror Page 5 Switch Operation 5.1 Address Table 5.2 Learning 5.3 Forwarding & Filtering 5.4 Store-and-Forward Page 6. Troubleshooting APPENDIX A A.1 Switch’s RJ-45Pin Assignments A.2 10/100Mbps, 10/100Base-TX A.3 RJ-45cable pin assignment