Planet Technology WGD-800 84

Category 3, 4 or 5 cable for 10Mbps connections or 100Ω Category 5 cable for 100Mbps connections. Also be sure that the length of any twisted-pair connection does not exceed 100 meters (328 feet).

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning WEEE Warning Table of Contents Page Page 1. INTRODUCTION 1.1 Packet Contents 1.2 How to Use This Manual 1.3Product Feature 1.4Product Specification Standard Compliance 2. INSTALLATION 2.1 Product Description 2.1.1 Product Overview 2.1.2 Switch Front Panel 2.1.3 LED Indications 2.2 Install the Switch 2.2.1 Desktop Installation 2.2.2 Rack Mounting 3.CONSOLE MANAGEMENT 3.1Connecting to the Switch 3.2 Login in the Console Interface 3.3 Console Management 3.4 Telnet login 3.5 Commands 3.5.2 Privileged Command 3.5.2.1 Clear command 3.5.2.2 Copy command 3.5.2.3 Disable command 3.5.2.4 Reboot command 3.5.2.5 Set command Page Page 3.5.2.6 Show command Page 4. WEB-BASEDMANAGEMENT 4.1 About Web-basedManagement 4.2 Preparing for Web Management 4.3 System Login 4.4 System 4.4.1 IP Configuration 4.4.2 SNMP 4.4.2.1 Theory 4.2.2.2 SNMP Configuration Contact: “OK” 3. Community Configuration Add Community: Read only: 4.4.3 Password 4.4.4 CONSOLE 4.4.5 System Upgrade 4.4.6 Saving Parameters 4.4.7 Parameters Backup & Recovery 4.4.8 Load Default 4.4.9 Reboot 4.5 Port Management 4.5.1 Port Configuration 4.5.2 Port Statistics 4.5.3 Port Band Restrict 4.6 Redundancy 4.6.1 Spanning Tree 1. Spanning Tree Protocol Bridge Protocol Data Units Creating a Stable STP Topology STP Port States Each port on a switch using STP exists is in one of the following five states: Blocking Listening Learning Forwarding 2. STP Parameters Port Priority Port Cost Default Spanning-TreeConfiguration Feature User-ChangeableSTA Parameters 3. Illustration of STP 4.6.2 Spanning Tree Configuration 1. Spanning Tree Configuration 2. Bridge Information 3. STP Port Configuration 4.6.3 Link Aggregation 4.7 Security 4.7.1 VLAN 4.7.1.1 Theory VLAN Description Port-basedVLAN IEEE 802.1Q VLANs Tagging Untagging 802.1Q VLAN Tags 802.1Q Tag Adding an IEEE802.1Q Tag Port VLAN ID 4.7.1.2 VLAN Configuration VLAN Confirutation Port List VLAN Member “Close” “Show VLAN Member” Understand nomenclature of the Switch Port Mode VLAN Membership Frame Leave single multiple Link Type Acces Trunk Access Trunk configuration: 4.7.2 MAC Address Bind 4.7.3 MAC Address Filtering 4.7.4 MAC Address Learning 4.7.5 MAC Address Aging Time 4.7.6 802.1X Port-BasedNetwork Access Control 4.7.6.1 Theory Authentication server Switch (802.1X device) „Ports in Authorized and Unauthorized States Page 4.7.6.2 802.1X Configuration Page Radius Server •RADIUS Server IP Address •Authentication Port(1-65535) •Share Key Page Active Directory Users and Computers 4.7.6.3 802.1X Client Configuration •Configure Sample: EAP-MD5Authentication Page Page 4.8 QoS 4.8.1 Understand QOS QoS Terminology 4.8.2 QOS Configuration 1. MAC-COSMapping 2. VLAN-COSMapping 3. 802.1p-CoSMapping 4. Port-COSMapping 5. COS-QueueMapping 6. Queue Management 4.9 Multicast 4.9.1 IGMP Snooping Theory IGMP Versions 1 and “report” “leave” IGMP Snooping Configuration “Enable” IGMP Snooping Status 4.10 Port Analysis 4.10.1 Port Analysis 4.10.2 Port Mirror 4.11 Storm Control 4.12 IP Stacking 4.12.1 About IP Stacking 4.12.2 IP Stacking Configuration •Master Switch configuration •Client Switch configuration Master switch “Saving parameters” 5. TROUBLE SHOOTING 5.1 Incorrect connections 5.1.1 Faulty or loose cables 5.1.2 Non-standardcables 5.1.3 Improper Network Topologies Page 6. APPENDIX 6.1 Console Port Pin Assignments 6.2 100BASE-TX/10BASE-TPin Assignments 7. APPENDIX-B „802.1Q VLAN Multi-UntaggedVLAN setting sample Add/Modify add close Egress Policy PVID=2 PVID=3 Part No. 2081-A92310-001