Installing the Mid/Woofers in Non-Factory Locations

If you have decided to install your EX Series II mid/woofers in locations other than those provided by the automobile manufacturer, make certain that the location you choose is clear of all obstructions, both in front of and behind the panel, before you proceed. Pay particular attention to window mechanisms and any body panels critical to the structural integrity of the vehicle. The mounting depths and cutout diameters of your EX Series II mid/woofers are listed with all the other important specifications at the end of this manual.

1.A paper template for marking the cutout holes is in the speaker carton

2.Cut a hole in the panel

3.Using the paper template, mark the locations of the four screw holes

4.Drill the holes with a 1/8" bit

5.Attach the screw clips to the car panel at the hole locations

6.Attach speaker wires to the crossover woofer terminals. Attach the red wire to the positive (+) terminal screw, and the black wire to the negative (-) terminal screw

7.Run wires from your amplifier or radio to the crossover. Attach these wires to the crossover input terminals. Remember to route them away from low level electrical cables and use grommets when passing through doors. Attach the red wire to the positive (+) terminal screw, and the black wire to the negative (-) terminal screw

8.Remove the mesh grille from the grille frame and pass the wire through the grille frame

9.Slip the faston connectors onto the input terminals on the mid/woofers. Be sure to attach the red wire to the positive (+) terminal, and the black wire to the negative (-) terminal

10.Place the speaker into the grille frame and line up the screw holes with the screw clips on the car panel

11.Secure the speaker/grille frame assembly to the car panel with the supplied screws

12.Place the mesh grille in the grille frame

EX2545 Special Instructions

The EX2545 has two break-away “tabs” to allow easy placement in tight locations

(see Figure 3). Remove only the tab(s) which allow the speaker to fit. Secure the speaker with at least two opposing tabs.

FIG. 3

GRAY AREA BREAKS OFF

EX System Tweeters

One important advantage of component systems is their ability, when properly installed, to improve the soundstage created by the music in your car. The soundstage is the musical “picture” made up of the instruments and vocalists. The difference in the soundstage will be dramatic depending on where you mount your tweeters. We recommend a simple experiment that will help you decide the best spot for your tweeters in your car. Here are the steps:

1.Complete the installation of your entire system except for the EX2500 tweeters.

2.Connect the wires provided with your tweeters to the tweeter terminals on your EX crossovers.

3.Without running the wires through doors or under upholstered panels, connect your EX tweeters to these wires.

4.Have a friend sit in the passenger’s seat while you sit in the driver’s seat, with tweeters temporarily taped in place.

5.With music playing, position the tweeters in different locations around the passenger compartment, listening for the differences caused from these placements. We recommend using vocals for this test. You will be able to determine in a short time the best location for your tweeters.

8

9

Page 4 Page 6
Page 5
Image 5
Polk Audio EX SERIES II owner manual Installing the Mid/Woofers in Non-Factory Locations, EX2545 Special Instructions
Page 4 Page 6

EX SERIES II specifications

Polk Audio has long been a respected name in the audio industry, and its EX Series II speakers continue this legacy with an impressive blend of performance, design, and value. Designed to deliver an immersive audio experience, the EX Series II is perfect for music lovers and movie enthusiasts alike.

One of the standout features of the EX Series II is its Dynamic Balance technology. This proprietary technology helps to eliminate distortion and provide a smooth, accurate sound profile. By utilizing a unique driver design, Polk ensures that every note across a wide frequency range is reproduced with clarity. The result is a balanced sound that captures the nuances of recordings, making it ideal for both music playback and surround sound systems.

The speakers in the EX Series II are constructed with high-quality materials, featuring lightweight, yet strong enclosures that minimize unwanted vibrations. This design characteristic not only enhances sound quality but also ensures durability over time. The sleek and modern appearance of the speakers means they can seamlessly integrate into any room’s décor, making them visually appealing as well.

Another impressive aspect of the EX Series II is its versatility. Whether you’re setting up a dedicated home theater or simply looking to enhance your everyday listening experience, these speakers shine. They are available in a range of configurations, including floor-standing, bookshelf, and center channel options, allowing users to build a customized audio setup that meets their specific needs.

Polk Audio also incorporates its patented Power Port technology in the EX Series II, which enhances low-frequency response by reducing turbulence and improving airflow. This innovative design results in deeper bass that you can feel while ensuring that the sound remains clear and articulated.

Additionally, the EX Series II is compatible with a range of amplifiers and receivers, making it easy to integrate into existing systems. The speakers are engineered to handle high power input, allowing them to produce loud volumes without sacrificing sound quality.

In conclusion, the Polk Audio EX Series II embodies the brand's dedication to quality and innovation. With features like Dynamic Balance technology, durable construction, versatile configurations, and enhanced bass response, these speakers are a strong choice for anyone looking to elevate their audio experience. Whether for movies, music, or gaming, the EX Series II delivers performance that promises to impress even the most discerning audiophiles.
Top Page Image Contents