IMPORTANT SAFETYINSTRUCTIONS
W ARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of
fire, electric shock and personal injury, including the following:
READ AND FOLLOW ALLINSTRUCTIONS.
There are certain applications for which this tool was designed. Porter-Cable strongly recommends that this tool
N OT be modified and/or used for any application other than for which it was designed. If you have any questions
relative to its application DO NOT use the tool until you have written Porter-Cable and we have advised you.
Technical Service Manager
Porter-Cable Corporation
4825 Highway 45 North, P. O. Box 2468
Jackson, TN 38302-2468
POLARIZED PLUGS: To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way . If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
1. KEEPWORK AREACLEAN. Cluttered areas and benches invite injuries.
2. AVOID DANGEROUS ENVIRONMENT.Dont expose power tools to rain. Don t use power tools in damp or
wet locations. Keep area well lit. A void chemical or corrosive environment. Do not use tool in presence of
flammable liquids or gases.
3. KEEPCHILDREN A W AY.Do not let visitors contact tool or extension cord. All visitors should be kept away
from work area.
4. S TORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or locked-up place out of
reach of children.
5. DON T FORCE TOOL. It will do the job better and safer at the rate for which it was intended.
6. USE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed.
7. DRESS PROPERLY.Do not wear loose clothing or jewelry. Loose clothing, draw strings and jewelry can be
caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear
protective hair covering to contain long hair .
8. USE SAFETY GLASSES. W ear safety glasses or goggles while operating power tools. Also face or dust
mask if operation creates dust. All persons in the area where power tools are being operated should also wear
safety glasses and face or dust mask. Refer to ANSI Z87.1 standard for appropriate recommendations.
9. SECURE WORK. Use clamp s or a vise to hold work. It s safer than using your hand and it frees both hands
to operate tool.
10. DO N T OV ER REA CH . Keep proper footing and balance at all times.
11. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have
repaired by authorized service facility . Inspect extension cords periodically and replace if damaged. Have all worn,
broken or lost parts replaced immediately. Keep handles dry, clean and free from oil and grease.
12.DISCONNECT TOOLS when not in use, before servicing, and when changing accessories such as blades,
bits, cutters, etc.
13. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting
wrenches are removed from the tool before turning it on.
14. AVOID UNINTENTIONAL STARTING.Do not carry a plugged-in tool with finger on switch. Be sure switch is off
when plugging in. Keep hands, body and clothing clear of blades, bits, cutters, etc. when plugging in the tool.
15.OUTDOOR USE EXTENSION CORDS. When tool is used out doors, use only extension cords marked
Suitable for use with out door appliances store indoors when not in use.
16. STAYALERT.Watch what you are doing. Use common sense. Do not operate tool when you are tired or while
under the influence of medication, alcohol or drugs.
17. CHECK DAMAGED PARTS.Before further use of the tool, a guard or other p art that is damaged should be
carefully checked to determine that it will operate properly and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of p arts, mounting, and any other conditions that may affect
its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized
service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced
by authorized service center. Do not use tool if switch does not turn it on and off.
18.KEEP GUARDS IN PLACE AND IN WORKING ORDER. Never wedge or tie lower guard open. Check
operation of lower guard before each use. Do not use if lower guard does not close briskly over saw blade.
CAUTION: If saw is dropped, lower guard may be bent, restricting full return.
19.KEEP BLADES CLEAN AND SHARP.Sharp blades minimize stalling and kickback.
2