To Level Mower Housing, Belt Removal

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE		BOTTOM EDGE
OF MOWER TO		OF MOWER TO
GROUND		GROUND
A	GROUND LINE	A

FIG. 19

SUSPENSION

ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 20

FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

• Before making any necessary adjustments, check that both front links are equal in length.

• If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

“D”

FIG. 21

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

FIG. 22

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 23)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

183046 specifications

The Poulan 183046 is a powerful and versatile chainsaw, designed to tackle a wide range of cutting tasks with ease. One of its standout features is the robust 18-inch cutting bar, allowing users to efficiently fell medium to large trees, prune branches, and handle firewood cutting. The length of the bar strikes a perfect balance between maneuverability and cutting capability, making it ideal for both novice users and seasoned professionals.

Powered by a reliable 42cc two-stroke engine, the Poulan 183046 delivers impressive performance. Its high power-to-weight ratio ensures that users can work for extended periods without experiencing fatigue. Furthermore, the engine is designed for easy starting, thanks to the chain brake and the choke lever, which help in reducing the effort required to initiate the engine.

One of the key technologies that set the Poulan 183046 apart is its advanced air filtration system. This system helps to prolong the life of the engine by keeping harmful debris and particles from entering and causing damage. Coupled with a tool-less fuel and oil cap, the chainsaw is designed for user convenience, making it simple to refuel and maintain.

Safety features are paramount in chainsaw design, and the Poulan 183046 does not disappoint. It comes equipped with a chain brake, which activates in the event of kickback, significantly reducing the risk of injury. Additionally, its ergonomic design includes a comfortable grip and anti-vibration technology, allowing users to maintain control even during prolonged use.

The Poulan 183046 is also engineered for durability, featuring high-quality materials that can withstand harsh outdoor conditions. Its design not only focuses on performance but also on providing a lasting tool that homeowners and professionals alike can rely on for their cutting needs.

Overall, the Poulan 183046 combines power, safety, and ease of use, appealing to a wide range of users from casual homeowners to dedicated landscapers. Its blend of advanced technologies and thoughtful design ensures that it remains a top choice in the competitive chainsaw market. Whether you're looking to tackle a tough job in your backyard or manage landscaping projects, the Poulan 183046 is engineered to get the job done efficiently and effectively.

Poulan 183046 To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal

Models: 183046