SERVICE AND ADJUSTMENTS

SEAT PAN

FIG. 29

HOOD

HEADLIGHT WIRE CONNECTOR

TERMINAL

KEPS NUT

COVER

 

HEX

BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

FIG. 30

TO REPLACE HEADLIGHT BULB

Raise hood.

Pull bulb holder out of the hole in the backside of the grill.

Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31)

Raise hood.

Unsnap headlight wire connector.

Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

To replace, reverse above procedure.

FIG. 31

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 32)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

GOVERNOR GOVERNOR

CONTROL LEVER CONTROL PLATE

HOLES “A”

CLAMP

THROTTLE

 

 

SCREW

CABLE

FIG. 32

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE T H E F A C T O R Y H I G H S P E E D S E T T I N G C A N B E DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y

23ADJUSTMENTS.

Page 23
Image 23
Poulan 183046 owner manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse, To Adjust Carburetor

183046 specifications

The Poulan 183046 is a powerful and versatile chainsaw, designed to tackle a wide range of cutting tasks with ease. One of its standout features is the robust 18-inch cutting bar, allowing users to efficiently fell medium to large trees, prune branches, and handle firewood cutting. The length of the bar strikes a perfect balance between maneuverability and cutting capability, making it ideal for both novice users and seasoned professionals.

Powered by a reliable 42cc two-stroke engine, the Poulan 183046 delivers impressive performance. Its high power-to-weight ratio ensures that users can work for extended periods without experiencing fatigue. Furthermore, the engine is designed for easy starting, thanks to the chain brake and the choke lever, which help in reducing the effort required to initiate the engine.

One of the key technologies that set the Poulan 183046 apart is its advanced air filtration system. This system helps to prolong the life of the engine by keeping harmful debris and particles from entering and causing damage. Coupled with a tool-less fuel and oil cap, the chainsaw is designed for user convenience, making it simple to refuel and maintain.

Safety features are paramount in chainsaw design, and the Poulan 183046 does not disappoint. It comes equipped with a chain brake, which activates in the event of kickback, significantly reducing the risk of injury. Additionally, its ergonomic design includes a comfortable grip and anti-vibration technology, allowing users to maintain control even during prolonged use.

The Poulan 183046 is also engineered for durability, featuring high-quality materials that can withstand harsh outdoor conditions. Its design not only focuses on performance but also on providing a lasting tool that homeowners and professionals alike can rely on for their cutting needs.

Overall, the Poulan 183046 combines power, safety, and ease of use, appealing to a wide range of users from casual homeowners to dedicated landscapers. Its blend of advanced technologies and thoughtful design ensures that it remains a top choice in the competitive chainsaw market. Whether you're looking to tackle a tough job in your backyard or manage landscaping projects, the Poulan 183046 is engineered to get the job done efficiently and effectively.