TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 22

NOTE: To seal punctures or prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer.Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualifi ed service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS”in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

1.Drain the fuel tank.

2.Start the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Do not store gasoline from one season to another.

ENGINE

 

• Replace your gasoline can if your can starts to rust.

See engine manual.

 

Rust and/or dirt in your gasoline will cause problems.

FUEL SYSTEM

 

• If possible, store your snow thrower indoors and cover

 

it to protect it from dust and dirt.

IMPORTANT: It is important to prevent gum deposits from

 

 

• Cover your snow thrower with a suitable protective cover

forming in essential fuel system parts such as carburetor,

 

 

that does not retain moisture.Do not use plastic.Plastic

fuel hose, or tank during storage.Also, alcohol blended fuels

 

 

cannot breathe, which allows condensation to form and

(called gasohol or using ethanol or methanol) can attract

 

 

will cause your snow thrower to rust.

moisture which leads to separation and formation of acids

 

 

IMPORTANT: Never cover snow thrower while engine/

during storage. Acidic gas can damage the fuel system of

 

an engine while in storage.

18

exhaust area is still warm.

 

 

Page 17 Page 19
Page 18
Image 18
Poulan 185156 owner manual Storage, Other
Page 17 Page 19

185156 specifications

The Poulan 185156 is a robust and versatile chainsaw designed for both residential and light commercial use, making it an excellent choice for homeowners, landscapers, and hobbyists alike. Engineered with a focus on power and ease of use, it delivers reliable performance for a variety of cutting tasks, from felling small trees to pruning branches and clearing brush.

One of the standout features of the Poulan 185156 is its powerful engine. Equipped with a reliable 18-inch guide bar, it provides ample cutting length to tackle larger logs and limbs with relative ease. The chainsaw's engine is designed to offer a balance of power and efficiency, ensuring that users can get the job done without constantly refueling. This is particularly beneficial for those who have larger areas to manage or for projects that require extended use.

The Poulan 185156 incorporates several innovative technologies to enhance the user's experience. One notable feature is its Easy Start system, which reduces the effort needed to start the engine. This is especially helpful for users who may struggle with traditional pull-start mechanisms. Additionally, the chainsaw features an automatic oiling system that ensures the chain and bar are properly lubricated during operation, resulting in smoother cuts and extended tool life.

Safety is also a primary consideration in the design of the Poulan 185156. The chainsaw is equipped with a chain brake system to prevent unwanted chain movement, enhancing user safety during operation. The comfortable grip and lightweight design contribute to reduced user fatigue, making it easier to handle for prolonged periods.

Durability remains a key characteristic of this chainsaw. Constructed with high-quality materials, it is built to withstand the rigors of outdoor use. The solid construction ensures that the Poulan 185156 can handle tough tasks while maintaining its performance over time.

In conclusion, the Poulan 185156 is a dependable chainsaw packed with features and technologies that prioritize performance, efficiency, and user safety. With its powerful engine, innovative starting system, and effective safety features, it stands out as a valuable tool for homeowners and professionals alike. Whether for landscaping, tree maintenance, or general yard work, the Poulan 185156 delivers the quality and reliability expected from a top-tier chainsaw.
Top Page Image Contents