MERLIN LEGEND Communications System Release 7.0 | Issue 1 | ||||
Pocket Reference |
| April 1999 | |||
|
|
|
|
| |
Reference Documents |
| 111 | |||
|
|
|
|
| |
|
|
| Technical Addendum |
| |
| Maintenance Error Codes |
|
| ||
| Error |
|
|
|
|
| Code | Description | Action |
| |
0001 | TIMEOUT COLD START: | No action required; however, if |
| ||
|
| System programming OK. | problem persists, troubleshoot |
| |
|
| the processor. |
| ||
|
|
|
|
| |
0002 | POWER UP WARM START: | No action required; however, if |
| ||
|
| System programming OK. | problem persists, troubleshoot |
| |
|
| the processor. |
| ||
|
|
|
|
| |
0003 | SOFTWARE COLD START: | If problem persists, troubleshoot |
| ||
|
| System programming OK. | the processor. |
| |
|
|
|
| ||
0004 | SOFTWARE WARM START: | If problem persists, troubleshoot |
| ||
|
| System programming OK. | the processor. |
| |
|
|
|
| ||
0005 | Reset - DIAGNOSTIC |
|
| ||
|
| SWITCH: |
|
| |
0006 | INCOMPLETE COLD START: If problem persists, troubleshoot |
| |||
|
| System | the processor. |
| |
|
|
|
| ||
|
| restart in progress. |
|
| |
0007 | SANITY TIMEOUT RESET: | Check module and/or |
| ||
|
| Faulty software, module, carrier, | processor. |
| |
|
|
|
| ||
|
| or processor sanity timer. |
|
| |
0008 | MAX RESET COUNT | If problem persists, troubleshoot |
| ||
|
| EXCEEDED: | the processor. |
| |
|
|
|
| ||
|
| System |
|
| |
|
| too many warm starts. |
|
| |
0009 | FRIGID START: | If processor was removed while |
| ||
|
| System restarted and initialized to | in use, system may perform |
| |
|
| defaults; also logged after System | frigid start because of loss of |
| |
|
| Erase. | system programming. Restore |
| |
|
| system as described in System |
| ||
|
|
|
|
| |
|
|
|
| Programming and Maintenance |
|
|
|
|
| (SPM). |
|
| 000A | POWER UP COLD START: | If problem persists, check |
| |
|
| RAM failure in processor; system | processor. |
| |
|
| programming OK. |
|
| |
| 000B | CARD | None. |
| |
|
| INSERTED/REMOVED: |
|
| |
| 000C | SLOT STREAM CNT | If problem persists, check |
| |
|
| EXCEEDED: | module. |
| |
|
|
|
| ||
|
| Slot generated excessive |
|
| |
|
| interrupts. |
|
| |
| 000D | FMWR NOT IN STANDBY | If problem persists, check |
| |
|
| MODE: | module. |
| |
|
|
|
| ||
|
| Module firmware not in standby |
|
| |
|
| mode. |
|
| |
| 000E | COMMAND BUFFER FULL: | If problem persists, check |
| |
|
|
|
| processor and module. |
|
| 000F | TASK RUNNING TOO LONG | None; if problem persists, check |
| |
|
|
|
| processor. |
|