MAINTENANCE

V-BELTS

Check V-belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual).

TheV-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer.Using other than OEM belts can cause personal injury or damage to the snow thrower.

AUGER GEAR CASE

•The gear case was fi lled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classifi cation SF-SJ. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 50 hours of operation or at least once a year if the snow thrower is not used for 50 hours in one year.

Check the crankcase oil level before starting the engine and after each fi ve (5) hours of continuous use. Tighten oil fi ll cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classifi cation SF-SJ.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with spark plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fi ll cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refi ll engine with oil through oil dipstick tube. Pour slowly. Do not overfi ll. For approximate capacity see “PRODUCT SPECIFICATIONS”section of this manual.

9.Use gauge on oil fi ll cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffl er as it could create a fi re hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs fi rst. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with spark plug.

•Keep fi nished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffl er and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Page 14 Page 16
Page 15
Image 15
Poulan 188047 owner manual Engine, Cleaning
Page 14 Page 16

188047 specifications

The Poulan 188047 is a powerful and versatile chainsaw designed to tackle a range of cutting tasks with efficiency and ease. Known for its robust construction and user-friendly features, this chainsaw has become a popular choice among both homeowners and professionals.

One of the standout features of the Poulan 188047 is its engine power. Equipped with a 42cc two-cycle engine, it provides ample power for cutting through tough materials. The engine is designed for optimal performance, offering a balance of power and fuel efficiency, making it an excellent tool for both light trimming and heavier cutting tasks.

In terms of design, the Poulan 188047 features a lightweight build which enhances maneuverability, allowing users to handle it comfortably for extended periods. The ergonomic design includes an anti-vibration handle that reduces fatigue, enabling operators to work more efficiently. The front guard is also designed to provide extra protection, ensuring safety during operation.

One of the key technologies incorporated in the Poulan 188047 is its easy start system. This innovation simplifies the starting process, making it accessible for users of all experience levels. The chainsaw also utilizes a tool-less chain tensioning system, allowing for quick adjustments without the need for additional tools. This feature saves valuable time, especially during larger cutting jobs when frequent adjustments may be necessary.

Another important characteristic of the Poulan 188047 is its 18-inch guide bar. This size strikes a balance between agility and reach, making it suitable for cutting firewood, felling small to medium-sized trees, and completing landscaping tasks. Coupled with its low-kickback chain, users can operate the chainsaw with confidence, knowing they have a reliable, safe cutting tool at their disposal.

The Poulan 188047 also features an automatic oiling system that lubricates the chain and bar during operation, prolonging the life of the chainsaw and ensuring smooth cutting performance. This system not only enhances durability but also minimizes the maintenance needed, allowing users to focus on their tasks without worrying about constantly checking oil levels.

In summary, the Poulan 188047 encapsulates a blend of power, convenience, and safety features that cater to a wide array of cutting needs. Its user-friendly technologies and ergonomic design make it a trusted choice for those seeking efficiency in their cutting tasks, whether at home or on the job site. With the Poulan 188047, users can expect reliable performance and ease of use, making it a valuable addition to any toolkit.
Top Page Image Contents