Poulan 188047 owner manual Storage, Other

TO REMOVE WHEELS (See Fig. 23)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL	OUTER HOLE
IN OUTER HOLE
OF AXLE ONLY)

AXLE

WHEEL WHEEL HUB

FIG. 23

NOTE: To seal punctures or prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer.Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualifi ed service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualifi ed service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS”in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

1.Drain the fuel tank.

2.Start the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Do not store gasoline from one season to another.

ENGINE		• Replace your gasoline can if your can starts to rust.
See engine manual.		Rust and/or dirt in your gasoline will cause problems.
FUEL SYSTEM		• If possible, store your snow thrower indoors and cover
		it to protect it from dust and dirt.
IMPORTANT: It is important to prevent gum deposits from
		• Cover your snow thrower with a suitable protective cover
forming in essential fuel system parts such as carburetor,
		that does not retain moisture.Do not use plastic.Plastic
fuel hose, or tank during storage.Also, alcohol blended fuels
		cannot breathe, which allows condensation to form and
(called gasohol or using ethanol or methanol) can attract
		will cause your snow thrower to rust.
moisture which leads to separation and formation of acids
		IMPORTANT: Never cover snow thrower while engine/
during storage. Acidic gas can damage the fuel system of
an engine while in storage.	18	exhaust area is still warm.