SERVICE AND ADJUSTMENTS

TO REPLACE MOTION DRIVE BELT (See Fig. 20)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

Remove belt from stationary idler and clutching idler.

Remove belt downward from around engine pulley.

Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keep- ers.

Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

Carefully work new belt down between transaxle belt keepers and onto the input pulley.

Slide belt into the center span keeper.

Pull belt toward front of tractor and roll around the top groove of engine pulley.

Install belt through stationary idler and clutching idler.

Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 21)

Block up axle securely.

Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

Repair tire and reassemble.

On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

Replace washers and snap retaining ring securely in axle groove.

Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING RING

AXLE COVER

ENGINE

PULLEY

CLUTCHING

IDLER

CENTER SPAN KEEPER

00811

STATIONARY IDLER

TRANSAXLE PULLEY

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 21

TO START ENGINE WITH A WEAK BATTERY (See Fig. 22)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow

FIG. 20

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

21

Page 21
Image 21
Poulan 190785 manual To Replace Motion Drive Belt See Fig, Front Wheel TOE-IN/CAMBER, To Remove Wheel for Repairs See Fig

190785 specifications

The Poulan 190785 is a powerful and versatile chainsaw designed for both professional and residential forestry tasks. This model is particularly noted for its reliability and efficiency, making it a popular choice among users who require a robust tool for cutting, pruning, and tree removal.

One of the standout features of the Poulan 190785 is its powerful engine. It typically comes equipped with a 2-cycle gas engine that delivers impressive horsepower, ensuring that users can tackle even the toughest jobs with ease. The engine design focuses on minimizing fuel consumption while maximizing power, which allows for longer operational periods before needing to refuel.

The chainsaw features a 18-inch bar and chain, providing an optimal cutting length for a variety of applications, from trimming branches to felling small to medium-sized trees. The chain speed is notably high, which enhances cutting efficiency and reduces the physical effort needed by the operator. Additionally, the bar is designed with a low kickback feature, enhancing safety during use.

In terms of usability, the Poulan 190785 incorporates several ergonomic designs. The comfortable handle is designed for better grip and control, reducing user fatigue during extended operation. The chainsaw also includes an automatic oiling system, which ensures that the chain operates smoothly, reducing wear and extending the tool's lifespan.

Safety is a priority with the Poulan 190785, which includes features such as a chain brake that immediately stops the chain in case of kickback, protecting the operator from potential injuries. The chainsaw’s lightweight construction further enhances its maneuverability, allowing users to easily navigate around their work environment.

Maintenance is made simpler with the Poulan 190785 due to its easy-access air filter and carburetor, facilitating routine checks and cleaning. This design consideration ensures that the chainsaw remains in peak operating condition, resulting in a longer service life.

In summary, the Poulan 190785 stands out as a well-rounded chainsaw option, combining power, safety, and ease of use. Whether you are a homeowner looking to maintain your yard or a professional needing a reliable tool for forestry work, the Poulan 190785 delivers performance and efficiency to get the job done effectively. Its durable construction and thoughtful features make it a worthwhile investment for anyone seeking a chainsaw they can count on.