6.Disconnect anti-sway bar from chassis bracket by removing retainer spring.

7.Disconnect suspension arms from rear deck brackets by removing retainer springs.

8.Disconnect front links from deck by removing retainer springs.

9.Raise lift lever to raise suspension arms.

Slide mower out from under tractor. IMPORTANT: If an attachment other than the mower deck is to be mounted on the tractor, remove the front links and hook the clutch spring Into square hole in frame.

TO INSTALL MOWER

1.Raise attachment lift lever to its highest position.

2.Slide mower under tractor with deflec- tor shield to right side of tractor.

3.Lower lift lever to its lowest position.

4.Connect front links to mower deck and secure with retainer springs.

5.Connect suspension arms to rear deck brackets and secure with retainer springs.

6.Connect anti-sway bar to chassis bracket and secure with retainer spring.

7.Push clutch cable housing guide into bracket, slide collar onto guide and secure with large retainer spring.

8.Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

9.Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjust- ment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

• Recheck measurements after adjusting.

Bottom edge of

Bottom edge of

mower to ground

mower to ground

 

00598

A

Ground Line

A

Suspension Arm

01553

Lift Link Adjustment Nut

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to side. If the following front-to-back adjustment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side. To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of trac- tor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2"

lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal num- ber of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

01268

Mandrel

“D” “D”

21

Page 20 Page 22
Page 21
Image 21
Poulan 191606 manual To Install Mower, To Level Mower Housing, SIDE-TO-SIDE Adjustment, FRONT-TO-BACK Adjustment
Page 20 Page 22

191606 specifications

The Poulan 191606 is a chainsaw that makes a solid addition to any home or workshop, designed primarily for both light and medium-duty tasks. This versatile tool is ideal for homeowners, landscapers, and DIY enthusiasts who require a reliable and efficient chainsaw for various cutting needs.

One of the standout features of the Poulan 191606 is its powerful engine. Equipped with a 2-cycle engine, it delivers sufficient power to cut through logs, branches, and dense foliage with ease. The engine is not only robust but also designed to be fuel-efficient, which means users can accomplish more work without frequently stopping to refuel.

The chainsaw boasts an 18-inch bar and chain, providing an excellent balance between reach and maneuverability. The length is suitable for cutting medium-sized trees and performing precise pruning tasks while still being manageable for users of all experience levels.

Another noteworthy characteristic of the Poulan 191606 is its ease of use. The chainsaw features an automatic oiling system that ensures consistent lubrication of the bar and chain, enhancing durability and extending the life of the tool. This feature reduces maintenance chores for users, allowing them to focus more on their cutting tasks.

Moreover, the Poulan 191606 is equipped with a simple starting system that includes an easy-to-pull starter mechanism, which minimizes the effort required to get the saw running. This user-friendly design makes it accessible for both novice and experienced operators.

For added safety, the Poulan 191606 is fitted with features like a chain brake, which is crucial for preventing kickback, ensuring that users can operate the saw with peace of mind. Additionally, the handle is designed for comfort and control, providing a secure grip that can help reduce fatigue during extended use.

In summary, the Poulan 191606 combines power, efficiency, and user-friendly features, making it a commendable choice for anyone in need of a reliable chainsaw. Its durable construction, automatic oiling system, and safety features make it suitable for a range of applications, from simple yard maintenance to more extensive landscaping projects, ensuring that users can tackle their tasks effectively. Whether you're trimming branches or cutting firewood, the Poulan 191606 is designed to deliver consistent performance and reliability.
Top Page Image Contents