2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

3.Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

Check wiring. See electrical wiring diagram in the Repair Parts section.

02614

Weak or Dead

Fully Charged

Battery

Battery

REPLACING BATTERY

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

1.Lift hood to raised position.

2.Remove terminal guard.

3.Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

4.Install new battery with terminals in same position as old battery.

5.Reinstall terminal guard.

6.First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

7.Connect BLACK grounding cable to negative (-) battery terminal with re- maining hex bolt and keps nut. Tighten securely

8.Close terminal access doors.

9.Close hood.

Keps Nut

Hex Bolt

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS- SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to re- connect the headlight wire connector.

Hood

Headlight

Wire

Connector

02141

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, see engine manual

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be nec-

Terminal

Access

Door

Terminal

Guard

Positive (Red) Cable

Negative (Black)

Cable24

essary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

Page 24
Image 24
Poulan 191606 manual To Adjust Carburetor

191606 specifications

The Poulan 191606 is a chainsaw that makes a solid addition to any home or workshop, designed primarily for both light and medium-duty tasks. This versatile tool is ideal for homeowners, landscapers, and DIY enthusiasts who require a reliable and efficient chainsaw for various cutting needs.

One of the standout features of the Poulan 191606 is its powerful engine. Equipped with a 2-cycle engine, it delivers sufficient power to cut through logs, branches, and dense foliage with ease. The engine is not only robust but also designed to be fuel-efficient, which means users can accomplish more work without frequently stopping to refuel.

The chainsaw boasts an 18-inch bar and chain, providing an excellent balance between reach and maneuverability. The length is suitable for cutting medium-sized trees and performing precise pruning tasks while still being manageable for users of all experience levels.

Another noteworthy characteristic of the Poulan 191606 is its ease of use. The chainsaw features an automatic oiling system that ensures consistent lubrication of the bar and chain, enhancing durability and extending the life of the tool. This feature reduces maintenance chores for users, allowing them to focus more on their cutting tasks.

Moreover, the Poulan 191606 is equipped with a simple starting system that includes an easy-to-pull starter mechanism, which minimizes the effort required to get the saw running. This user-friendly design makes it accessible for both novice and experienced operators.

For added safety, the Poulan 191606 is fitted with features like a chain brake, which is crucial for preventing kickback, ensuring that users can operate the saw with peace of mind. Additionally, the handle is designed for comfort and control, providing a secure grip that can help reduce fatigue during extended use.

In summary, the Poulan 191606 combines power, efficiency, and user-friendly features, making it a commendable choice for anyone in need of a reliable chainsaw. Its durable construction, automatic oiling system, and safety features make it suitable for a range of applications, from simple yard maintenance to more extensive landscaping projects, ensuring that users can tackle their tasks effectively. Whether you're trimming branches or cutting firewood, the Poulan 191606 is designed to deliver consistent performance and reliability.