Before Starting the Engine, ADD Gasoline See Fig

OPERATION

TRACTION DRIVE

CONTROL LEVER

DRIVE SPEED

CONTROL LEVER

FIG. 16

TO ADJUST SKID PLATES (See Fig. 17)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 18)

The engine on your snow thrower has been shipped, from the factory, already ﬁlled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil ﬁ ll cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overﬁll.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 18)

•Fill fuel tank to bottom of tank ﬁ ller neck. Do not over- ﬁll. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open ﬂame.

CAUTION: Alcohol blended fuels (called gas- ohol or using ethanol or methanol) can attract moisture which leads to separation and for- mation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next sea- son. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the rear 1/2" hex nut only, then moving skid plate to desired position.Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION (LOW GROUND CLEARANCE)

AUGER

HOUSING

SKID PLATE

1/2" HEX NUT

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 17

SCRAPER BAR

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn

CHOKE CONTROL

SAFETY

IGNITION

KEY

RECOIL

STARTER

HANDLE

THROTTLE PRIMER ENGINE OIL FILL CAP / DIPSTICK

GASOLINE

FILLER CAP

FUEL SHUT-

OFF VALVE

almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement.

Replace a damaged or worn scraper bar.

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 18

192034 specifications

The Poulan 192034 is a versatile and high-performing chainsaw that caters to both professional users and homeowners looking for a reliable tool for various cutting tasks. Designed for durability and efficiency, the Poulan 192034 excels in handling both light and heavy-duty applications. One of its standout features is its powerful engine, which ensures optimal cutting performance even in tough conditions.

Equipped with a 38cc two-stroke engine, the Poulan 192034 delivers impressive power, allowing users to tackle everything from tree trimming to firewood cutting. The engine is designed to provide a good balance of torque and speed, enabling users to make quick work of dense materials. Furthermore, the chainsaw comes with a 16-inch bar, offering a perfect size for both residential and commercial cutting needs, making it ideal for various applications including pruning, felling small trees, and cutting logs.

One of the remarkable technologies employed in the Poulan 192034 is the Easy Start system, which significantly reduces the effort required to start the chainsaw. This innovative feature allows users to get to work quickly without the frustration often associated with starting gas-powered tools. In addition to Easy Start, the chainsaw is equipped with an automatic oiling system that ensures the chain and bar receive the necessary lubrication during operation, minimizing wear and prolonging the life of these critical components.

User comfort is also a key focus in the design of the Poulan 192034. The chainsaw features a lightweight and ergonomic design that reduces user fatigue during extended use. The anti-vibration technology incorporated into the handle absorbs shocks, making it easier to handle the tool for longer periods without discomfort. This is particularly valuable for professionals who may be using the chainsaw for multiple hours at a time.

Another advantage of the Poulan 192034 is its safety features, including a chain brake that engages quickly in the event of kickback, protecting the user from potential injuries. The easy-access air filter and tool-less chain tensioning system enhance convenience, allowing users to maintain the chainsaw effortlessly.

Overall, the Poulan 192034 stands out as a reliable, efficient, and user-friendly chainsaw equipped with essential features and technologies that meet the needs of both casual users and professionals alike. With its solid performance and thoughtful design, it is a valuable addition to any toolkit.

Poulan 192034 Before Starting the Engine, To Adjust Skid Plates See Fig, ADD Gasoline See Fig

Models: 192034