TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 22

NOTE: To seal punctures or prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer.Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualifi ed service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS”in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

 

IMPORTANT: It is important to prevent gum deposits from

 

forming in essential fuel system parts such as carburetor,

 

fuel hose, or tank during storage.Also, alcohol blended fuels

 

(called gasohol or using ethanol or methanol) can attract

 

moisture which leads to separation and formation of acids

 

during storage. Acidic gas can damage the fuel system of

 

an engine while in storage.

18

 

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture.Do not use plastic.Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm.

Page 17 Page 19
Page 18
Image 18
Poulan 192034 owner manual Storage, Other
Page 17 Page 19

192034 specifications

The Poulan 192034 is a versatile and high-performing chainsaw that caters to both professional users and homeowners looking for a reliable tool for various cutting tasks. Designed for durability and efficiency, the Poulan 192034 excels in handling both light and heavy-duty applications. One of its standout features is its powerful engine, which ensures optimal cutting performance even in tough conditions.

Equipped with a 38cc two-stroke engine, the Poulan 192034 delivers impressive power, allowing users to tackle everything from tree trimming to firewood cutting. The engine is designed to provide a good balance of torque and speed, enabling users to make quick work of dense materials. Furthermore, the chainsaw comes with a 16-inch bar, offering a perfect size for both residential and commercial cutting needs, making it ideal for various applications including pruning, felling small trees, and cutting logs.

One of the remarkable technologies employed in the Poulan 192034 is the Easy Start system, which significantly reduces the effort required to start the chainsaw. This innovative feature allows users to get to work quickly without the frustration often associated with starting gas-powered tools. In addition to Easy Start, the chainsaw is equipped with an automatic oiling system that ensures the chain and bar receive the necessary lubrication during operation, minimizing wear and prolonging the life of these critical components.

User comfort is also a key focus in the design of the Poulan 192034. The chainsaw features a lightweight and ergonomic design that reduces user fatigue during extended use. The anti-vibration technology incorporated into the handle absorbs shocks, making it easier to handle the tool for longer periods without discomfort. This is particularly valuable for professionals who may be using the chainsaw for multiple hours at a time.

Another advantage of the Poulan 192034 is its safety features, including a chain brake that engages quickly in the event of kickback, protecting the user from potential injuries. The easy-access air filter and tool-less chain tensioning system enhance convenience, allowing users to maintain the chainsaw effortlessly.

Overall, the Poulan 192034 stands out as a reliable, efficient, and user-friendly chainsaw equipped with essential features and technologies that meet the needs of both casual users and professionals alike. With its solid performance and thoughtful design, it is a valuable addition to any toolkit.
Top Page Image Contents